[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

linksys WMP11 oversized packet received issue

im planning to build a AP using Openbsd i currently have a Linksys WMP11
Card, i was able to manage setting it up but i get a lot of the following
message, that eventually kills wifi connection and so does the rest of the
wired network. (please see below)

wi0: oversized packet received (wi_dat_len=65535, wi_status=0x0)
wi0: oversized packet received (wi_dat_len=65535, wi_status=0x0)
wi0: oversized packet received (wi_dat_len=65535, wi_status=0x0)
wi0: oversized packet received (wi_dat_len=65535, wi_status=0x0)
wi0: oversized packet received (wi_dat_len=65535, wi_status=0x0)

the wifi card was successfully detected.

wi0 at pci0 dev 9 function 0 "Intersil PRISM2.5" rev 0x01: irq 11
wi0: PRISM2.5 ISL3874A(Mini-PCI), Firmware 1.0.5 (primary), 1.3.4 (station),
address 00:06:25:a7:e

currently i took out the card and using the wired network going to my
openbsd box.

maybe anyone of you guys could help me out, would appreciate it greatly! :)

$ dmesg
OpenBSD 3.7 (GENERIC) #50: Sun Mar 20 00:01:57 MST 2005
cpu0: Intel Pentium/MMX ("GenuineIntel" 586-class) 234 MHz
cpu0: F00F bug workaround installed
real mem = 268017664 (261736K)
avail mem = 237785088 (232212K)
using 3297 buffers containing 13504512 bytes (13188K) of memory
mainbus0 (root)
bios0 at mainbus0: AT/286+(00) BIOS, date 07/15/95, BIOS32 rev. 0 @ 0xfdb70
apm0 at bios0: Power Management spec V1.2
apm0: AC on, battery charge unknown
pcibios0 at bios0: rev 2.1 @ 0xf0000/0x10000
pcibios0: PCI BIOS has 6 Interrupt Routing table entries
pcibios0: PCI Interrupt Router at 000:01:0 ("SIS 85C503 System" rev 0x00)
pcibios0: PCI bus #0 is the last bus
bios0: ROM list: 0xc0000/0x8000 0xc8000/0x800
cpu0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (bios)
pchb0 at pci0 dev 0 function 0 "SIS 5597/5598 Host" rev 0x02
pcib0 at pci0 dev 1 function 0 "SIS 85C503 System" rev 0x01
pciide0 at pci0 dev 1 function 1 "SIS 5513 EIDE" rev 0xd0: 5597/5598: DMA,
el 0 configured to compatibility, channel 1 configured to compatibility
wd0 at pciide0 channel 0 drive 0: <Maxtor 91021U2>
wd0: 16-sector PIO, LBA, 9770MB, 20010816 sectors
atapiscsi0 at pciide0 channel 0 drive 1
scsibus0 at atapiscsi0: 2 targets
probe(atapiscsi0:0:0): Check Condition (error 0x7f) on opcode 0x0
AT BLOCK #: 16713471 (decimal)cd0 at scsibus0 targ 0 lun 0: <CREATIVE,
E-CF, 1.04> SCSI0 5/cdrom removable
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2
cd0(pciide0:0:1): using PIO mode 4, DMA mode 2
pciide0: channel 1 disabled (no drives)
xl0 at pci0 dev 11 function 0 "3Com 3c905C 100Base-TX" rev 0x78: irq 11,
exphy0 at xl0 phy 24: 3Com internal media interface
rl0 at pci0 dev 13 function 0 "Realtek 8139" rev 0x10: irq 10 address
rlphy0 at rl0 phy 0: RTL internal phy
vga1 at pci0 dev 15 function 0 "Trident TGUI 9660" rev 0xd3
wsdisplay0 at vga1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
isa0 at pcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0 (mux 1 ignored for console): console keyboard, using
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
sysbeep0 at pcppi0
lpt0 at isa0 port 0x378/4 irq 7
npx0 at isa0 port 0xf0/16: using exception 16
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pccom1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
biomask f365 netmask ff65 ttymask ffe7
pctr: 586-class performance counters and user-level cycle counter enabled
dkcsum: wd0 matched BIOS disk 80
root on wd0a
rootdev=0x0 rrootdev=0x300 rawdev=0x302