[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Install 3.7 on Compaq Proliant 2500 failed

Hello misc,

I'm trying to install OpenBSD 3.7 from original CD's, but without any
success. I'm googling for some time now, but I haven't find a solution
to this problem.

panic: cannot open disk, 0xf0/0x3f0, error 6

- Compaq Proliant 2500
- bi-processors motherboard, but only one installed (Pentium Pro_(_at_)_200MHz)
- 256 MB RAM
- 3 x 4,3 GB Ultra-Wide SCSI hard drives
- Symbios Logic 53c875 SCSI Host Adapter
- Compaq SMART-2/P RAID controller
- Compaq Netelligent PCI Lan Adapter

Somebody can help me for this one?

Thanks in advance.


>> OpenBSD/i386 CDBOOT 1.00
boot> machine mem +0xF000000_(_at_)_0x1000000
Region 0: type 1 at 0x0 for 638KB
Region 1: type 1 at 0x100000 for 261120KB
Low ram: 638KB  High ram: 15360KB
Total free memory: 261758KB
boot> boot cd0a:/3.7/i386/bsd -c
booting cd0a:/3.7/i386/bsd: 4686240+945680 [52+241328+223324]=0x5d0864
entry point at 0x100120

[ using 465076 bytes of bsd ELF symbol table ]
Copyright (c) 1982, 1986, 1989, 1991, 1993
        The Regents of the University of California.  All rights reserved.
Copyright (c) 1995-2005 OpenBSD. All rights reserved.  http://www.OpenBSD.org

OpenBSD 3.7 (GENERIC) #50: Sun Mar 20 00:01:57 MST 2005
cpu0: Intel Pentium Pro ("GenuineIntel" 686-class, 256KB L2 cache) 199 MHz
real mem  = 268017664 (261736K)
avail mem = 237793280 (232220K)
using 3297 buffers containing 13504512 bytes (13188K) of memory
User Kernel Config
UKC> disable pcibios
254 pcibios0 disabled
UKC> disable eisa
232 eisa0 disabled
UKC> exit
mainbus0 (root)
bios0 at mainbus0: AT/286+(00) BIOS, date 12/30/98, BIOS32 rev. 0 @ 0xf0000
pcibios at bios0 function 0x1a not configured
bios0: ROM list: 0xc0000/0x8000 0xc8000/0x4000 0xe8000/0x6000 0xee000/0x2000!
cpu0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 "Intel 82441FX" rev 0x02
ppb0 at pci0 dev 13 function 0 "IBM 82351 PCI-PCI" rev 0x01
pci1 at ppb0 bus 1
vga1 at pci1 dev 6 function 0 "Cirrus Logic CL-GD5430" rev 0x22
wsdisplay0 at vga1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
tl0 at pci1 dev 7 function 0 "Compaq ProLiant Netelligent 10/100 TX" rev 0x10: irq 5 address 00:80:5f:a6:ee:92
nsphy0 at tl0 phy 1: DP83840 10/100 PHY, rev. 0
ukphy0 at tl0 phy 31: Generic IEEE 802.3u media interface
ukphy0: OUI 0x100014, model 0x0001, rev. 4
siop0 at pci1 dev 9 function 0 "Symbios Logic 53c875" rev 0x03: irq 10, using 4K of on-board RAM
scsibus0 at siop0: 16 targets
ppb1 at pci0 dev 15 function 0 "IBM 82351 PCI-PCI" rev 0x01
pci2 at ppb1 bus 2
cac0 at pci2 dev 0 function 0 "Compaq SMART2P RAID" rev 0x02: irq 9 Compaq SMART-2/P
scsibus1 at cac0: 1 targets
sd0 at scsibus1 targ 0 lun 0: <Compaq, RAID5 volume #, > SCSI2 0/direct fixed
sd0: 8187MB, 2055 cyl, 255 head, 32 sec, 512 bytes/sec, 16768800 sec total
"Compaq EISA" rev 0x07 at pci0 dev 20 function 0 not configured
eisa at mainbus0 not configured
isa0 at mainbus0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0 (mux 1 ignored for console): console keyboard, using wsdisplay0
wdc0 at isa0 port 0x1f0/8 irq 14
atapiscsi0 at wdc0 channel 0 drive 0
scsibus2 at atapiscsi0: 2 targets
cd0 at scsibus2 targ 0 lun 0: <HITACHI, CDR-7930, 1023> SCSI0 5/cdrom removable
cd0(wdc0:0:0): using BIOS timings
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
sysbeep0 at pcppi0
lpt2 at isa0 port 0x3bc/4: polled
npx0 at isa0 port 0xf0/16: using exception 16
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pccom0: console
pccom1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec
biomask ffc5 netmask ffe5 ttymask ffe7
pctr: 686-class user-level performance counters enabled
mtrr: Pentium Pro MTRR support
dkcsum: sd0 matched BIOS disk 80
root on wd15a
rootdev=0xf0 rrootdev=0x3f0 rawdev=0x3f2
panic: cannot open disk, 0xf0/0x3f0, error 6
Stopped at      Debugger+0x4:   leave
ddb> trace
Debugger(3,3f2,d06d3f58,84,3f2) at Debugger+0x4
panic(d04dd860,f0,3f0,6,d06d3d8c) at panic+0x63
dk_mountroot(0,0,d06d3fa0,d01fde23,10000000) at dk_mountroot+0x177
vfs_mountroot(10000000,ef6007ff,d05c,0,0) at vfs_mountroot+0x51
main(0,0,0,0,0) at main+0x43b
ddb> ps
   PID   PPID   PGRP    UID  S       FLAGS  WAIT       COMMAND
     2      0      0      0  3    0x100204  kmalloc    kmthread
     1      0      0      0  3         0x4  initexec   swapper
*    0     -1      0      0  7     0x80204             swapper