[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: sgi 02 latest snapshot CD37.iso boot problems



Hello Mark and List, thank you for the reply and assistance.

I have tried "Booting from CD-ROM installation media" with cd38.iso but the 02 does not recognize the media.

When I go into the maintenance menu and boot -f dksc(0,4,8)boot, it boots to /bsd but panic at no init

I am going to try to setup a boot net to another openbsd machine. Total newbie but on the learning curve!

I just had a successful install on a Panasonic Toughbook CF-25, i386 is newbie able. : )

Thanks again for your help.

Script started on Fri Aug 12 14:54:44 2005
openbsd37# cu -l tty00
Connected
                        Running power-on diagnostics...

System Maintenance Menu

1) Start System
2) Install System Software
3) Run Diagnostics
4) Recover System
5) Enter Command Monitor


Option? 5 Command Monitor. Type "exit" to return to the menu.

ls dksc(0,4,8)
dksc(0,4,8):

boot

exit

Running power-on diagnostics...




System Maintenance Menu

1) Start System
2) Install System Software
3) Run Diagnostics
4) Recover System
5) Enter Command Monitor


Option? 2


Installing System Software...

                      Press <Esc> to return to the menu.




1) Remote Tape 2) Remote Directory 3)[Local CD-ROM] X) Local Tape

     *a) Local SCSI CD-ROM drive 4


Enter 1-4 to select source type, a to select the source, <esc> to quit,

or <enter> to start: 3



1) Remote Tape  2) Remote Directory  3)[Local CD-ROM]  X) Local Tape

     *a) Local SCSI CD-ROM drive 4


Enter 1-4 to select source type, a to select the source, <esc> to quit,

or <enter> to start: 3



1) Remote Tape  2) Remote Directory  3)[Local CD-ROM]  X) Local Tape

     *a) Local SCSI CD-ROM drive 4


Enter 1-4 to select source type, a to select the source, <esc> to quit,

or <enter> to start:

System Maintenance Menu

1) Start System
2) Install System Software
3) Run Diagnostics
4) Recover System
5) Enter Command Monitor


Option? 5 Command Monitor. Type "exit" to return to the menu.

printenv
diskless=0

dbaud=9600

volume=80

sgilogo=y

monitor=h

TimeZone=PST8PDT

netaddr=192.0.2.1

AutoLoad=No

console=d

SystemPartition=pci(0)scsi(0)disk(1)rdisk(0)partition(8)

ConsoleOut=serial(0)

ConsoleIn=serial(0)

cpufreq=180

eaddr=08:00:69:02:df:19

OSLoadPartition=pci(0)scsi(0)disk(1)rdisk(0)partition(0)

OSLoadFilename=/bsd

OSLoader=sash

hinv
                  System: IP32

               Processor: 180 Mhz R5000, with FPU

    Primary I-cache size: 32 Kbytes

    Primary D-cache size: 32 Kbytes

    Secondary cache size: 512 Kbytes

             Memory size: 128 Mbytes

                Graphics: CRM, Rev C

                   Audio: A3 version 1

               SCSI Disk: scsi(0)disk(1)

              SCSI CDROM: scsi(0)cdrom(4)

boot -f dksc(0,4,8)boot
34192+1264 entry: 0x80010120

SystemPartition pci(0)scsi(0)disk(1)rdisk(0)partition(8)
arg 0: dksc(0,4,8)boot
arg 1: ConsoleIn=serial(0)
arg 2: ConsoleOut=serial(0)
arg 3: SystemPartition=pci(0)scsi(0)disk(1)rdisk(0)partition(8)
arg 4: OSLoader=sash
arg 5: OSLoadPartition=pci(0)scsi(0)disk(1)rdisk(0)partition(0)
arg 6: OSLoadFilename=/bsd

OpenBSD/sgi Arcbios boot
Boot: pci(0)scsi(0)disk(1)rdisk(0)partition(0)/bsd
|/-\|Loading ELF64 file
0xffffffff80100000:0x30e0a0, Zero 0xffffffff8040e0a0:0x5d2a0, Loading symbol table
Start at 0xffffffff80100000
ARCS32 Firmware Version 1.10
SR=34010080
Found SGI-IP32, setting up.
Initial setup done, switching console.


NOTE: TLB code too large, using trampolines

[ using 263136 bytes of bsd ELF symbol table ]

Copyright (c) 1982, 1986, 1989, 1991, 1993

	The Regents of the University of California.  All rights reserved.

Copyright (c) 1995-2005 OpenBSD. All rights reserved. http://www.OpenBSD.org


OpenBSD 3.7 (GENERIC) #89: Sun Mar 20 18:32:30 MST 2005

   deraadt_(_at_)_sgi_(_dot_)_openbsd_(_dot_)_org:/usr/src/sys/arch/sgi/compile/GENERIC

real mem = 134217728

rsvd mem = 7020544

avail mem = 108883968

using 1638 buffers containing 6709248 bytes of memory

mainbus0 (root)

cpu0 at mainbus0: MIPS R5000 CPU rev 2.1 180 MHz with R5000 based FPC rev 1.0

cpu0: cache L1-I 32KB D 32KB 2 way, L2 512KB direct

macebus0 at mainbus0: crime rev 10.1

clock0 at macebus0: TOD with DS1687, ticker on int5 using count register.

macepcibr0 at macebus0: mace rev 1, host system O2

pci0 at macepcibr0 bus 0

ahc0 at pci0 dev 1 function 0 "Adaptec AIC-7880" rev 0x00: irq 9

ahc0: Host Adapter Bios disabled.  Using default SCSI device parameters

scsibus0 at ahc0: 16 targets

ahc0: target 1 using 8bit transfers

ahc0: target 1 using asynchronous transfers

sd0 at scsibus0 targ 1 lun 0: <IBM, DNES-309170Y, SA30> SCSI3 0/direct fixed

sd0: 8748MB, 11474 cyl, 5 head, 312 sec, 512 bytes/sec, 17916240 sec total

cd0 at scsibus0 targ 4 lun 0: <TOSHIBA, CD-ROM XM-5701TA, 0167> SCSI2 5/cdrom removable

ahc1 at pci0 dev 2 function 0 "Adaptec AIC-7880" rev 0x00: irq 10

ahc1: Host Adapter Bios disabled.  Using default SCSI device parameters

scsibus1 at ahc1: 16 targets

com0 at macebus0: ns16550a, 16 byte fifo

com0: console

com1 at macebus0: ns16550a, 16 byte fifo

mec0 at macebus0: MAC-110 rev 1, address 08:00:69:02:df:19

nsphy0 at mec0 phy 8: DP83840 10/100 PHY, rev. 1

mavb0 at macebus0: AD1843 rev 1

audio0 at mavb0

boot device: sd0.

root device (default sd0a):

swap device (default sd0b):

root on sd0a

ahc0: target 1 using 16bit transfers

ahc0: target 1 synchronous at 10.0MHz, offset = 0x8

rootdev=0x0 rrootdev=0x900 rawdev=0x902

warning: /dev/console does not exist

init: not found

panic: no init

Stopped at      Debugger+0x4:   jr      ra

		nop

RUN AT LEAST 'trace' AND 'ps' AND INCLUDE OUTPUT WHEN REPORTING THIS PANIC!

DO NOT EVEN BOTHER REPORTING THIS WITHOUT INCLUDING THAT INFORMATION!

ddb> trace

Debugger+0x4 (ffffffffffffffff,ffffffffffffffff,500,d) sp ffffffffc6a93eb0 ra f

fffffff801b7d58, sz 0

panic+0xe0 (ffffffffffffffff,ffffffffffffffff,500,d) sp ffffffffc6a93eb0 ra fff

fffff801927dc, sz 96

start_init+0x23c (ffffffffffffffff,ffffffffffffffff,500,d) sp ffffffffc6a93f10 r

a ffffffff803601a8, sz 176

proc_trampoline+0x48 (ffffffffffffffff,ffffffffffffffff,500,d) sp ffffffffc6a93

fc0 ra 0, sz 0

User-level: pid 1

ddb> ps

  PID   PPID   PGRP    UID  S       FLAGS  WAIT       COMMAND

    8      0      0      0  3    0x100204  crypto_wa  crypto

    7      0      0      0  3    0x100204  aiodoned   aiodoned

    6      0      0      0  3    0x100204  syncer     update

    5      0      0      0  3    0x100204  cleaner    cleaner

    4      0      0      0  3    0x100204  reaper     reaper

    3      0      0      0  3    0x100204  pgdaemon   pagedaemon

    2      0      0      0  3    0x100204  kmalloc    kmthread

*    1      0      0      0  7         0x4             swapper

    0     -1      0      0  3     0x80204  scheduler  swapper

ddb> dmesg

NOTE: TLB code too large, using trampolines

[ using 263136 bytes of bsd ELF symbol table ]

Copyright (c) 1982, 1986, 1989, 1991, 1993

       The Regents of the University of California.  All rights reserved.

Copyright (c) 1995-2005 OpenBSD. All rights reserved. http://www.OpenBSD.org


OpenBSD 3.7 (GENERIC) #89: Sun Mar 20 18:32:30 MST 2005

   deraadt_(_at_)_sgi_(_dot_)_openbsd_(_dot_)_org:/usr/src/sys/arch/sgi/compile/GENERIC

real mem = 134217728

rsvd mem = 7020544

avail mem = 108883968

using 1638 buffers containing 6709248 bytes of memory

mainbus0 (root)

cpu0 at mainbus0: MIPS R5000 CPU rev 2.1 180 MHz with R5000 based FPC rev 1.0

cpu0: cache L1-I 32KB D 32KB 2 way, L2 512KB direct

macebus0 at mainbus0: crime rev 10.1

clock0 at macebus0: TOD with DS1687, ticker on int5 using count register.

macepcibr0 at macebus0: mace rev 1, host system O2

pci0 at macepcibr0 bus 0

ahc0 at pci0 dev 1 function 0 "Adaptec AIC-7880" rev 0x00: irq 9

ahc0: Host Adapter Bios disabled.  Using default SCSI device parameters

scsibus0 at ahc0: 16 targets

--db_more--ahc0: target 1 using 8bit transfers

--db_more--ahc0: target 1 using asynchronous transfers

--db_more--sd0 at scsibus0 targ 1 lun 0: <IBM, DNES-309170Y, SA30> SCSI3 0/direct fixed

--db_more--sd0: 8748MB, 11474 cyl, 5 head, 312 sec, 512 bytes/sec, 17916240 sec total

--db_more--cd0 at scsibus0 targ 4 lun 0: <TOSHIBA, CD-ROM XM-5701TA, 0167> SCSI2 5/cdrom r

--db_more--removable

--db_more--ahc1 at pci0 dev 2 function 0 "Adaptec AIC-7880" rev 0x00: irq 10

--db_more--ahc1: Host Adapter Bios disabled. Using default SCSI device parameters

--db_more--scsibus1 at ahc1: 16 targets

--db_more--com0 at macebus0: ns16550a, 16 byte fifo

--db_more--com0: console

--db_more--com1 at macebus0: ns16550a, 16 byte fifo

--db_more--mec0 at macebus0: MAC-110 rev 1, address 08:00:69:02:df:19

--db_more--nsphy0 at mec0 phy 8: DP83840 10/100 PHY, rev. 1

--db_more--mavb0 at macebus0: AD1843 rev 1

--db_more--audio0 at mavb0

--db_more--boot device: sd0.

--db_more--root device (default sd0a):

--db_more--swap device (default sd0b):

--db_more--root on sd0a

--db_more--ahc0: target 1 using 16bit transfers

--db_more--ahc0: target 1 synchronous at 10.0MHz, offset = 0x8

--db_more--rootdev=0x0 rrootdev=0x900 rawdev=0x902

--db_more--warning: /dev/console does not exist

--db_more--init: not found

--db_more--panic: no init

--db_more--Stopped at      Debugger+0x4:   jr      ra

--db_more--                nop

--db_more--R

From: Mark Kettenis <mark_(_dot_)_kettenis_(_at_)_xs4all_(_dot_)_nl>
To: misc_(_at_)_openbsd_(_dot_)_org
CC: bypos_(_at_)_hotmail_(_dot_)_com
Subject: Re: sgi 02 latest snapshot CD37.iso boot problems
Date: Fri, 12 Aug 2005 09:53:49 +0200 (CEST)

Please reread the current INSTALL.sgi again, in particular the section
on "Booting from CD-ROM installation media".

It should no longer be necessary to enter the Command Monitor to boot
from CD-ROM; just choose "Install System Software" from the System
Maintenance Menu.

Mark


_________________________________________________________________
Is your PC infected? Get a FREE online computer virus scan from McAfee. Security. http://clinic.mcafee.com/clinic/ibuy/campaign.asp?cid=3963




Visit your host, monkey.org