Intel EtherExpress PRO/100 Mobile Adapter unsupported?

[Volker Kindermann <openbsd_(_at_)_secspace_(_dot_)_de>]

Hi,

recently I have bought an Intel PCMCIA network card: Intel EtherExpress
PRO/100 Mobile Adapter. It has the Intel Part Number MBLA1600.

While trying to configure it, I encounter problems.

I run OpenBSD 3.2 release (with security-patches) and if I insert the
card, I get:

Nov 15 11:24:05 argus /bsd: pcmcia0: CIS version PC Card Standard 5.0
Nov 15 11:24:05 argus /bsd: pcmcia0: CIS info: Intel, EtherExpress(TM)
PRO/100 PC Card Mobile Adapter16, PRO/100 M16A, 1.00 Nov 15 11:24:05
argus /bsd: pcmcia0: Manufacturer code 0x89, product 0x10a Nov 15
11:24:05 argus /bsd: pcmcia0: function 0: network adapter, ccr addr 800
mask 3 Nov 15 11:24:05 argus /bsd: pcmcia0: function 0, config table
entry 1: I/O card; irq mask 8ebc; iomask 4, iospace 0-f; memspace
0-fff0; mwait_required rdybsy_active io8 io16 irqpulse irqlevel
powerdown Nov 15 11:24:05 argus /bsd: xe0 at pcmcia0 function 0 "Intel,
EtherExpress(TM) PRO/100 PC Card Mobile Adapter16, PRO/100 M16A" port
0xa000/16: address 00:a0:c9:bc:09:5e Nov 15 11:24:05 argus /bsd: ukphy0
at xe0 phy 0: Generic IEEE 802.3u media interface Nov 15 11:24:05 argus
/bsd: ukphy0: OUI 0x00057d, model 0x0000, rev. 0 Nov 15 11:24:05 argus
/bsd: ukphy1 at xe0 phy 16: Generic IEEE 802.3u media interface Nov 15
11:24:05 argus /bsd: ukphy1: OUI 0x00057d, model 0x0000, rev. 0 Nov 15
11:24:05 argus /bsd: ifmedia_match: multiple match for 0x20/0xfffffff


ifconfig -a shows:

lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 33224
	inet 127.0.0.1 netmask 0xff000000 
lo1: flags=8008<LOOPBACK,MULTICAST> mtu 33224
fxp0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
	address: 00:10:a4:8d:57:f7
	media: Ethernet autoselect (100baseTX full-duplex)
	status: active
	inet 192.168.17.7 netmask 0xffffff00 broadcast 192.168.17.255
pflog0: flags=0<> mtu 33224
tun0: flags=10<POINTOPOINT> mtu 3000
tun1: flags=10<POINTOPOINT> mtu 3000
bridge0: flags=0<> mtu 1500
bridge1: flags=0<> mtu 1500
vlan0: flags=0<> mtu 1500
	address: 00:00:00:00:00:00
vlan1: flags=0<> mtu 1500
	address: 00:00:00:00:00:00
xe0: flags=8822<BROADCAST,NOTRAILERS,SIMPLEX,MULTICAST> mtu 1500
	address: 00:a0:c9:bc:09:5e
	media: Ethernet autoselect instance 1
	status: no carrier

Even if I try to start the interface with a valid IP and a cable
attached, I won't get any networking connection.

If I start the interface manually, I get:

Nov 15 11:52:47 argus /bsd: ifmedia_match: multiple match for
0x10000026/0xfffffff
Nov 15 11:52:59 argus /bsd: xe0: device timeout


Is there a possibility to get this card to work?

Thank you very much
 -volker