[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Console not working as expected



I have two OpenBSD 3.0 machines.  One of them is on -current, the other is on -release.  The -current machine is trying to console into the -release machine, and almost nothing happens.  If I set up the null modem cable, and run "cu -l /dev/tty00" I can watch the -release machine boot up, from the boot> prompt to when it echo's the date and time.  I believe that is the last step before giving the login prompt.  After the date is echoed, the console is non-responsive.  I can login, however, via the directly connected keyboard, and there are no problems there.  If I watch the boot sequence on the -release machine, after boot> it says "switching console to com0".  The null modem cable DID work until I wiped the system and reinstalled 3.0.  There are no differences between working config and non-working config.  I was messing around with partition table, and since I didn't have anything important on it, I just wiped and started over.  When I login via root on the keyboard, it ec!
hos the root login warning on the console.  Console boot output from the -release machine following the signature.

-- 
Peter Hessler
<yodadoa_(_at_)_yahoo_(_dot_)_com>



boot>
booting hd0a:/bsd: 3698688+327680+773316+[136392+169862]=0x5de91a start=0xe0100020
entry point at 0x100020
 pciinfo 0xe064d140
[ using 306258 bytes of bsd a.out symbol table ]
Copyright (c) 1982, 1986, 1989, 1991, 1993
        The Regents of the University of California.  All rights reserved.
Copyright (c) 1995-2001 OpenBSD. All rights reserved.  http://www.OpenBSD.org

OpenBSD 3.0 (GENERIC) #94: Thu Oct 18 14:48:27 MDT 2001
    deraadt_(_at_)_i386_(_dot_)_openbsd_(_dot_)_org:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: F00F bug workaround installed
cpu0: Intel Pentium/MMX ("GenuineIntel" 586-class) 234 MHz
cpu0: FPU,V86,DE,PSE,TSC,MSR,MCE,CX8,MMX
real mem  = 66695168 (65132K)
avail mem = 56520704 (55196K)
using 839 buffers containing 3436544 bytes (3356K) of memory
mainbus0 (root)
bios0 at mainbus0: AT/286+(ce) BIOS, date 10/30/97, BIOS32 rev. 0 @ 0xfb340
apm0 at bios0: Power Management spec V1.2
apm0: AC on, battery charge unknown
pcibios0 at bios0: rev. 2.1 @ 0xf0000/0xb808
pcibios0: PCI BIOS has 5 Interrupt Routing table entries
pcibios0: PCI Exclusive IRQs: 10 11
pcibios0: PCI Interrupt Router at 000:07:0 ("Intel 82371AB PIIX4 ISA" rev 0x00) pcibios0: PCI bus #0 is the last bus
bios0: ROM list: 0xc0000/0x8000
pci0 at mainbus0 bus 0: configuration mode 1 (bios)
pchb0 at pci0 dev 0 function 0 "Intel 82439TX System" rev 0x01
pcib0 at pci0 dev 7 function 0 "Intel 82371AB PIIX4 ISA" rev 0x01
pciide0 at pci0 dev 7 function 1 "Intel 82371AB IDE" rev 0x01: DMA, channel 0 wired to compatibility, channel 1 wired to compatibility
wd0 at pciide0 channel 0 drive 0: <QUANTUM FIREBALL_TM1280A>
wd0: 16-sector PIO, LBA, 1222MB, 2484 cyl, 16 head, 63 sec, 2503872 sectors
wd1 at pciide0 channel 0 drive 1: <WDC AC28400R>
wd1: 16-sector PIO, LBA, 8063MB, 16383 cyl, 16 head, 63 sec, 16514064 sectors
wd0(pciide0:0:0): using PIO mode 4, DMA mode 2
wd1(pciide0:0:1): using PIO mode 4, Ultra-DMA mode 2
atapiscsi0 at pciide0 channel 1 drive 1
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 0 lun 0: <E-IDE, CD-ROM 36X/AKU, U10I> SCSI0 5/cdrom remova
ble
cd0(pciide0:1:1): using PIO mode 4, Ultra-DMA mode 2
uhci0 at pci0 dev 7 function 2 "Intel 82371AB USB" rev 0x01: irq 11
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: vendor 0x0000 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
"Intel 82371AB Power Mgmt" rev 0x01 at pci0 dev 7 function 3 not configured
vga1 at pci0 dev 13 function 0 "Trident TGUI 9660" rev 0xd3
wsdisplay0 at vga1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
xl0 at pci0 dev 15 function 0 "3Com 3c905B 100Base-TX" rev 0x64: irq 10 address 00:50:04:84:e0:ca
ukphy0 at xl0 phy 24: Generic IEEE 802.3u media interface
ukphy0: OUI 0x001018, model 0x0012, rev. 0
isa0 at pcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
ep0 at isa0 port 0x300/16 irq 5: address 00:20:af:d7:db:8f, utp/aui (default utp)
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
sysbeep0 at pcppi0
lpt0 at isa0 port 0x378/4 irq 7
npx0 at isa0 port 0xf0/16: using exception 16
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pccom0: console
pccom1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec
biomask c840 netmask cc60 ttymask cce2
pctr: 586-class performance counters and user-level cycle counter enabled
dkcsum: wd0 matched BIOS disk 80
dkcsum: wd1 matched BIOS disk 81
root on wd0a
rootdev=0x0 rrootdev=0x300 rawdev=0x302
Automatic boot in progress: starting file system checks.
/dev/rwd0a: file system is clean; not checking
/dev/rwd0d: file system is clean; not checking
/dev/rwd1a: file system is clean; not checking
setting tty flags
pf enabled
starting network
starting system logger
starting rpc daemons:.
savecore: no core dump
checking quotas: done.
building ps databases: kvm dev.
clearing /tmp
starting pre-securelevel daemons:.
setting kernel security level: kern.securelevel: 0 -> 1
preserving editor files
creating runtime link editor directory cache.
starting network daemons:.
starting local daemons:.
standard daemons: cron.
Sat Dec  8 14:08:18 PST 2001



Visit your host, monkey.org