IDE CD-Rom (Not Detected)

[Rob <falcon_(_at_)_usinternet_(_dot_)_com>]

Hello,
      I have a Dell Dimension P75t (Using P133mhz chip) w/40mb RAM.  It has
two hard drives on IDE channel 0 and a Samsung 32x CD player on IDE channel
1 set as master.  The openbsd floppy28.fs image does not seem to detect
this drive nor does a full ftp install with 'generic release'.  I had a
friend update the kernel to 'generic stable' from the CVS tree.  I will try
most anything to get this device to work but please be patient with me as I
am new to openbsd.  I should also add that the cd-rom is picked up by a
ms-dos boot disk with generic cdrom.sys driver and mscdex.exe.

Sincerely,

Rob

OpenBSD 2.8 (GENERIC) #399: Mon Nov 6 10:59:23 MST 2000
deraadt_(_at_)_i386_(_dot_)_openbsd_(_dot_)_org:/usr/src/sys/arch/i386/compile/GENERIC cpu0: F00F
bug workaround installed cpu0: Intel Pentium (P54C) ("GenuineIntel"
586-class) 133 MHz cpu0: FPU,V86,DE,PSE,TSC,MSR,MCE,CX8 real mem =
41529344 (40556K) avail mem = 33427456 (32644K) using 532 buffers
containing 2179072 bytes (2128K) of memory mainbus0 (root) bios0 at
mainbus0: AT/286+(00) BIOS, date 06/10/96, BIOS32 rev. 0 @ 0xfc750 pcibios0
at bios0: rev. 2.1 found at 0xf0000[0x10000] pcibios0: PCI BIOS has 6
Interrupt Routing table entries pcibios0: PCI bus #0 is the last bus pci0
at mainbus0 bus 0: configuration mode 1 (bios) pchb0 at pci0 dev 0 function
0 "Intel 82437FX (Triton)" rev 0x02 pcib0 at pci0 dev 7 function 0 "Intel
82371FB (Triton) PCI-ISA" rev 0x02 pciide0 at pci0 dev 7 function 1 "Intel
82371FB (Triton) IDE" rev 0x02: DMA, channel 0 wired to compatibility,
channel 1 wired to compatibility wd0 at pciide0 channel 0 drive 0: wd0: can
use 32-bit, PIO mode 4, DMA mode 2 wd0: 16-sector PIO, LBA, 2423MB, 4924
cyl, 16 head, 63 sec, 4963392 sectors wd1 at pciide0 channel 0 drive 1:
wd1: can use 32-bit, PIO mode 4, DMA mode 2 wd1: 8-sector PIO, LBA, 1039MB,
2112 cyl, 16 head, 63 sec, 2128896 sectors pciide0: channel 0 interrupting
at irq 14 wd0(pciide0:0:0): using PIO mode 4, DMA mode 2 (using DMA data
transfers) wd1(pciide0:0:1): using PIO mode 4, DMA mode 2 (using DMA data
transfers) "S3 Trio32/64" rev 0x53 at pci0 dev 8 function 0 not configured
xl0 at pci0 dev 13 function 0 "3Com 3c905B 100Base-TX" rev 0x24: irq 10xl0:
command never completed! address 00:10:4b:6f:9c:99 exphy0 at xl0 phy 24:
3Com internal media interface xl0: command never completed! isa0 at pcib0
isadma0 at isa0 pcppi0 at isa0 port 0x61 midi0 at pcppi0: sysbeep0 at
pcppi0 lpt0 at isa0 port 0x378/4 irq 7 npx0 at isa0 port 0xf0/16: using
exception 16 pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pccom1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo vt0 at isa0 port
0x60/16 irq 1: vga 80 col, color, 8 scr, mf2-kbd pms0 at vt0 irq 12 fdc0 at
isa0 port 0x3f0/6 irq 6 drq 2 fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head,
18 sec biomask 4040 netmask 4440 ttymask 54c2 pctr: 586-class performance
counters and user-level cycle counter enabled dkcsum: wd0 matched BIOS disk
80 wd1: no disk label dkcsum: wd1 matched BIOS disk 81 root on wd0a
rootdev=0x0 rrootdev=0x300 rawdev=0x302