[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Slow login with ftp and ssh

Hi everyone,

I've got a problem I could really use some help with.

I just built a new server and I'm seeing some extremely slow
logins over the network. I checked the mail archive and the only
thing I found was slow ssh logins do to improperly working DNS.
This does NOT seem to be the case for me. I am using the IP
addresses and not the hostnames.

Trying to login over ftp or ssh (the only two services running)
I'll typically have to wait around 45 sec's before I get a shell.
Logging into ftp I'll get the "Connected" message but then I'll have
to wait 45 seconds or so to actually get in.

My main guess right now is the nic driver. From bootup I got the nic
info and when I recompiled the kernel I left in the dc0 and ukphy
drivers which I saw in the dmesg. I _believe_ this was happening even
before I recompiled the kernel (yes, believe, I don't quite remember
for sure). Looking at the GENERIC kernel conf I can see that UKPHY is
for "unknown" which has me a little bit suspicious. The card is a
Netgear FA310TX Rev-D2.

Any ideas on ways to troubleshoot this or some help would be greatly

Jason Stout

OpenBSD 2.7 (conf) #0: Mon Sep 11 12:50:25 PDT 2000
cpu0: Intel Pentium III ("GenuineIntel" 686-class, 512KB L2 cache) 555 MHz
real mem  = 266956800 (260700K)
avail mem = 247209984 (241416K)
using 3284 buffers containing 13451264 bytes (13136K) of memory
mainbus0 (root)
bios0 at mainbus0: AT/286+(f3) BIOS, date 10/22/99
apm0 at bios0: Power Management spec V1.2
apm0: AC on, battery charge unknown
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 "Intel 82810E Memory Controller Hub" rev
0x03: RNG(10)
"Intel 82810E Graphics Controller" rev 0x03 at pci0 dev 1 function 0 not
ppb0 at pci0 dev 30 function 0 "Intel 82801AA Hub-to-PCI" rev 0x02
pci1 at ppb0 bus 1
dc0 at pci1 dev 8 function 0 "Lite-On PNIC" rev 0x20: irq 11 address
ukphy0 at dc0 phy 1: Generic IEEE 802.3u media interface
ukphy0: OUI 0x001018, model 0x0021, rev. 2
pcib0 at pci0 dev 31 function 0 "Intel 82801AA LPC Interface" rev 0x02
pciide0 at pci0 dev 31 function 1 "Intel 82801AA IDE" rev 0x02: DMA,
channel 0 wired to compatibility, channel 1 wired to compatibility
wd0 at pciide0 channel 0 drive 0: <Maxtor 52049H4>
wd0: can use 32-bit, PIO mode 4, DMA mode 2, Ultra-DMA mode 4
wd0: 16-sector PIO, LBA, 19541MB, 16383 cyl, 16 head, 63 sec, 40020624
pciide0: channel 0 interrupting at irq 14
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 4 (using DMA data
atapiscsi0 at pciide0 channel 1
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 0 lun 0: <ATAPI CD, ROM      MARS52, 1i> SCSI0 5/cdrom
cd0: can use 32-bit, PIO mode 4, DMA mode 2, Ultra-DMA mode 2
pciide0: channel 1 interrupting at irq 15
cd0(pciide0:1:0): using PIO mode 4, Ultra-DMA mode 2 (using DMA data
"Intel 82801AA USB" rev 0x02 at pci0 dev 31 function 2 not configured
"Intel 82801AA SMBus" rev 0x02 at pci0 dev 31 function 3 not configured
isa0 at pcib0
isadma0 at isa0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
sysbeep0 at pcppi0
lpt0 at isa0 port 0x378/4 irq 7
npx0 at isa0 port 0xf0/16: using exception 16
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pccom1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
vt0 at isa0 port 0x60/16 irq 1: vga 80 col, color, 8 scr, mf2-kbd
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec
biomask c040 netmask c840 ttymask c8c2
pctr: 686-class user-level performance counters enabled
dkcsum: wd0 matched BIOS disk 80
root on wd0a
rootdev=0x0 rrootdev=0x300 rawdev=0x302

FREE! The World's Best Email Address @email.com
Reserve your name now at http://www.email.com

Visit your host, monkey.org