[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Various nasties in 2.5 install...



Ok... So I installed OpenBSD the other day, about 5 times.

I can't seem to get it to boot off of the hard drive.  It
boots up decently with the install floppy (floppy25.fs),
but refuses to even start booting kernels off of the hard
drive.  I get the following immediately after the machine
is turned on and has completed its POST:

Using Drive: 0 Partition: 3

The machine just sits there at that point.  Here's the output
of fdisk:

Disk: wd0       geometry: 527/32/63 [1062432 sectors]
Offset: 0       Signatures: 0xAA55,0x0
         Starting        Ending
 #: id  cyl  hd sec -  cyl  hd sec [     start -       size]
----------------------------------------------------------------------
 0: 00    0   0   0 -    0   0   0 [         0 -          0] unused
 1: 00    0   0   0 -    0   0   0 [         0 -          0] unused
 2: 00    0   0   0 -    0   0   0 [         0 -          0] unused
*3: A6    0   1   1 -  526  31  63 [        63 -    1062369] OpenBSD

Here's the output of disklabel:

# /dev/rwd0c:
type: ESDI
disk: ESDI/IDE disk
label: ST5660A
flags:
bytes/sector: 512
sectors/track: 63
tracks/cylinder: 16
sectors/cylinder: 1008
cylinders: 1057
total sectors: 1066184
rpm: 3600
interleave: 1
trackskew: 0
cylinderskew: 0
headswitch: 0           # milliseconds
track-to-track seek: 0  # milliseconds
drivedata: 0

16 partitions:
#        size   offset   fstype   [fsize bsize   cpg]
  a:  1000000       63   4.2BSD     1024  8192    16   # (Cyl.    0*- 992*)
  b:    66121  1000063     swap                        # (Cyl.  992*- 1057*)
  c:  1066184        0   unused        0     0         # (Cyl.    0*- 1057*)

Now I'm assuming the problem lies somehwere in how my disk is laid out, but
I'm not sure where, if at all...  I've tried using installboot, but that
was pretty fruitless apart from some education.

Here's my my dmesg output:


OpenBSD 2.5 (RAMDISK) #136: Fri Apr 16 09:25:05 MDT 1999
    deraadt_(_at_)_i386_(_dot_)_openbsd_(_dot_)_org:/usr/src/sys/arch/i386/compile/RAMDISK
cpu0: F00F bug workaround installed
cpu0: Intel Pentium (P54C) ("GenuineIntel" 586-class) 90 MHz
cpu0: FPU,V86,DE,PSE,TSC,MSR,MCE,CX8
BIOS mem  = 654336 conventional, 49283072 extended
real mem  = 49938432
avail mem = 42442752
using 635 buffers containing 2600960 bytes of memory
mainbus0 (root)
bios0 at mainbus0: AT/286+(00) BIOS, date 10/10/95
bios0: pciinfo 0xf053700c diskinfo 0xf0537028 cksumlen 1 memmap 0xf05370c4
pci0 at mainbus0 bus 0: configuration mode 2 (bios)
pchb0 at pci0 dev 0 function 0 "Intel 82434LX/NX (Mercury/Neptune) PCI/Cache/DRAM" rev 0x11
"PC Technology RZ1000" rev 0x01 at pci0 dev 1 function 0 not configured
"Intel 82378IB PCI-ISA (System I/O)" rev 0x03 at pci0 dev 2 function 0 not configured
"ATI Technologies Mach64 CT" rev 0x09 at pci0 dev 14 function 0 not configured
isa0 at mainbus0
isadma0 at isa0
wdc0 at isa0 port 0x1f0-0x1f7 irq 14
atapibus0 at wdc0
wd0 at wdc0 drive 0: <ST5660A>
wd0: 520MB, 1057 cyl, 16 head, 63 sec, 512 bytes/sec, 1066184 sec total
wd0: using 16-sector 16-bit pio transfers, lba addressing (256KB cache)
wd1 at wdc0 drive 1: <Maxtor 7245 AT>
wd1: 234MB, 967 cyl, 16 head, 31 sec, 512 bytes/sec, 479632 sec total
wd1: using 16-sector 16-bit pio transfers, chs addressing (64KB cache)
wdc1 at isa0 port 0x170-0x177 irq 15
atapibus1 at wdc1
acd0 at atapibus1 drive 0: <FX810T4, a03> ATAPI 5/cdrom removable
acd0: 1377Kb/sec, 256Kb cache, audio play, 255 volume levels
we1 at isa0 port 0x300-0x31f iomem 0xcc000-0xcffff irq 10: SMC8216/SMC8216C (16-bit)
we1: Ethernet address 00:00:c0:9f:7c:b0
npx0 at isa0 port 0xf0-0xff: using exception 16
pccom0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, 16 byte fifo
pccom1 at isa0 port 0x2f8-0x2ff irq 3: ns16550a, 16 byte fifo
vt0 at isa0 port 0x60-0x6f irq 1: generic VGA, 80 col, color, 8 scr, mf2-kbd
fdc0 at isa0 port 0x3f0-0x3f5 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec
biomask c040 netmask c440 ttymask c442
root device? wd0a
root on wd0a
rd0: fixed, 3560 blocks
rootdev=0x0 rrootdev=0x300 rawdev=0x302

Thanks for your help...

-- 
Dave Henderson,
Network Security Administration,
The IT Department Inc.
http://www.itdepartment.com