[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

OpenBSD 2.9

To: bugs_(_at_)_openbsd_(_dot_)_org
Subject: OpenBSD 2.9
From: Monah Baki <mbaki_(_at_)_orblynx_(_dot_)_com>
Date: Thu, 14 Jun 2001 12:13:34 -0400

Attached is the dmesg output of one of our Network engine servers using OpenBSD 2.8. Installation runs perfectly with OpenBSD 2.7 and 2.8. I ordered a 2.9 CD which I received and tried installing it, I get the following error message

Fatal page fault in supervisor mode.
trap type 6 code 0
eip e01e7b3a cs 8 eflags 10202 cr2 14 cp10
panic: trap

Press any key to reboot.

This problem I've never encountered with previous versions, so I had to go back and install OpenBSD2.8.

Thanks.

ction 0 not configured
pciide0 at pci0 dev 7 function 1 "Intel 82371AB IDE (PIIX4)" rev 0x01: DMA, channel 0 wired to compatibility, channel 1 wired to compatibility
atapiscsi0 at pciide0 channel 1
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 1 lun 0: <TEAC, CD-224E, 1.5A> SCSI0 5/cdrom removable
cd0: can use 32-bit, PIO mode 4, DMA mode 2
pciide0: channel 1 interrupting at irq 15
cd0(pciide0:1:1): using PIO mode 4, DMA mode 2 (using DMA data transfers)
"Intel 82371AB USB (PIIX4)" rev 0x01 at pci0 dev 7 function 2 not configured
"Intel 82371AB Power Management (PIIX4)" rev 0x02 at pci0 dev 7 function 3 not configured
fxp0 at pci0 dev 17 function 0 "Intel 82557" rev 0x08: irq 10, address 00:d0:a8:00:a4:ba
inphy0 at fxp0 phy 1: i82555 10/100 media interface, rev. 4
fxp1 at pci0 dev 18 function 0 "Intel 82557" rev 0x08: irq 5, address 00:d0:a8:00:a4:bb
inphy1 at fxp1 phy 1: i82555 10/100 media interface, rev. 4
ppb1 at pci0 dev 20 function 0 "DEC DECchip 21152 PCI-PCI" rev 0x03
pci2 at ppb1 bus 2
ahc1 at pci2 dev 15 function 0 "Adaptec(2) AHA-2940U2 Ultra2" rev 0x00: irq 11
ahc1: Wide Channel A, SCSI Id=7, 16/255 SCBs
scsibus1 at ahc1: 16 targets
ahc1: target 0 using 16bit transfers
ahc1: target 0 synchronous at 40.0MHz, offset = 0xf
sd0 at scsibus1 targ 0 lun 0: <SEAGATE, ST39103LW, 0002> SCSI2 0/direct fixed
sd0: 8683MB, 9772 cyl, 6 head, 303 sec, 512 bytes/sec, 17783240 sec total
isa0 at mainbus0
isadma0 at isa0
npx0 at isa0 port 0xf0/16: using exception 16
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pccom1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
vt0 at isa0 port 0x60/16 irq 1: vga 80 col, color, 8 scr, mf2-kbd
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec
biomask 8840 netmask 8c60 ttymask 8c62
rd0: fixed, 3560 blocks
rootdev=0x1100 rrootdev=0x2f00 rawdev=0x2f02
syncing disks... done

The operating system has halted.
Please press any key to reboot.

rebooting...
OpenBSD 2.8 (GENERIC) #399: Mon Nov  6 10:59:23 MST 2000
    deraadt_(_at_)_i386_(_dot_)_openbsd_(_dot_)_org:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: Intel Pentium III (Coppermine) ("GenuineIntel" 686-class) 596 MHz
cpu0: FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SYS,MTRR,PGE,MCA,CMOV,PAT,PSE36,SER,MMX,FXSR,SIMD
real mem  = 1073328128 (1048172K)
avail mem = 991158272 (967928K)
using 5689 buffers containing 53768192 bytes (52508K) of memory
mainbus0 (root)
bios0 at mainbus0: AT/286+(00) BIOS, date 07/15/95, BIOS32 rev. 0 @ 0xfdb50
pcibios0 at bios0: rev. 2.1 found at 0xf0000[0x10000]
pcibios0: PCI BIOS has 8 Interrupt Routing table entries
pcibios0: PCI bus #2 is the last bus
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 "Intel 82440BX PCI-AGP" rev 0x00
ppb0 at pci0 dev 1 function 0 "Intel 82440BX AGP" rev 0x00
pci1 at ppb0 bus 1
"Chips and Technologies 69000" rev 0x64 at pci1 dev 0 function 0 not configured
pcib0 at pci0 dev 7 function 0 "Intel 82371AB PIIX4 ISA" rev 0x02
pciide0 at pci0 dev 7 function 1 "Intel 82371AB IDE (PIIX4)" rev 0x01: DMA, channel 0 wired to compatibility, channel 1 wired to compatibility
atapiscsi0 at pciide0 channel 1
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 1 lun 0: <TEAC, CD-224E, 1.5A> SCSI0 5/cdrom removable
cd0: can use 32-bit, PIO mode 4, DMA mode 2
pciide0: channel 1 interrupting at irq 15
cd0(pciide0:1:1): using PIO mode 4, DMA mode 2 (using DMA data transfers)
"Intel 82371AB USB (PIIX4)" rev 0x01 at pci0 dev 7 function 2 not configured
"Intel 82371AB Power Management (PIIX4)" rev 0x02 at pci0 dev 7 function 3 not configured
fxp0 at pci0 dev 17 function 0 "Intel 82557" rev 0x08: irq 10, address 00:d0:a8:00:a4:ba
inphy0 at fxp0 phy 1: i82555 10/100 media interface, rev. 4
fxp1 at pci0 dev 18 function 0 "Intel 82557" rev 0x08: irq 5, address 00:d0:a8:00:a4:bb
inphy1 at fxp1 phy 1: i82555 10/100 media interface, rev. 4
ppb1 at pci0 dev 20 function 0 "DEC DECchip 21152 PCI-PCI" rev 0x03
pci2 at ppb1 bus 2
ahc1 at pci2 dev 15 function 0 "Adaptec(2) AHA-2940U2 Ultra2" rev 0x00: irq 11
ahc1: Wide Channel A, SCSI Id=7, 16/255 SCBs
scsibus1 at ahc1: 16 targets
ahc1: target 0 using 16bit transfers
ahc1: target 0 synchronous at 40.0MHz, offset = 0xf
sd0 at scsibus1 targ 0 lun 0: <SEAGATE, ST39103LW, 0002> SCSI2 0/direct fixed
sd0: 8683MB, 9772 cyl, 6 head, 303 sec, 512 bytes/sec, 17783240 sec total
isa0 at pcib0
isadma0 at isa0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
sysbeep0 at pcppi0
lpt0 at isa0 port 0x378/4 irq 7
npx0 at isa0 port 0xf0/16: using exception 16
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pccom1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
vt0 at isa0 port 0x60/16 irq 1: vga 80 col, color, 8 scr, mf2-kbd
pms0 at vt0 irq 12
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec
biomask 8840 netmask 8c60 ttymask 9ce2
pctr: 686-class user-level performance counters enabled
mtrr: Pentium Pro MTRR support
dkcsum: sd0 matched BIOS disk 80
root on sd0a
rootdev=0x400 rrootdev=0xd00 rawdev=0xd02
syncing disks... done
rebooting...
OpenBSD 2.8 (GENERIC) #399: Mon Nov  6 10:59:23 MST 2000
    deraadt_(_at_)_i386_(_dot_)_openbsd_(_dot_)_org:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: Intel Pentium III (Coppermine) ("GenuineIntel" 686-class) 596 MHz
cpu0: FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SYS,MTRR,PGE,MCA,CMOV,PAT,PSE36,SER,MMX,FXSR,SIMD
real mem  = 1073328128 (1048172K)
avail mem = 991158272 (967928K)
using 5689 buffers containing 53768192 bytes (52508K) of memory
mainbus0 (root)
bios0 at mainbus0: AT/286+(00) BIOS, date 07/15/95, BIOS32 rev. 0 @ 0xfdb50
pcibios0 at bios0: rev. 2.1 found at 0xf0000[0x10000]
pcibios0: PCI BIOS has 8 Interrupt Routing table entries
pcibios0: PCI bus #2 is the last bus
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 "Intel 82440BX PCI-AGP" rev 0x00
ppb0 at pci0 dev 1 function 0 "Intel 82440BX AGP" rev 0x00
pci1 at ppb0 bus 1
"Chips and Technologies 69000" rev 0x64 at pci1 dev 0 function 0 not configured
pcib0 at pci0 dev 7 function 0 "Intel 82371AB PIIX4 ISA" rev 0x02
pciide0 at pci0 dev 7 function 1 "Intel 82371AB IDE (PIIX4)" rev 0x01: DMA, channel 0 wired to compatibility, channel 1 wired to compatibility
atapiscsi0 at pciide0 channel 1
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 1 lun 0: <TEAC, CD-224E, 1.5A> SCSI0 5/cdrom removable
cd0: can use 32-bit, PIO mode 4, DMA mode 2
pciide0: channel 1 interrupting at irq 15
cd0(pciide0:1:1): using PIO mode 4, DMA mode 2 (using DMA data transfers)
"Intel 82371AB USB (PIIX4)" rev 0x01 at pci0 dev 7 function 2 not configured
"Intel 82371AB Power Management (PIIX4)" rev 0x02 at pci0 dev 7 function 3 not configured
fxp0 at pci0 dev 17 function 0 "Intel 82557" rev 0x08: irq 10, address 00:d0:a8:00:a4:ba
inphy0 at fxp0 phy 1: i82555 10/100 media interface, rev. 4
fxp1 at pci0 dev 18 function 0 "Intel 82557" rev 0x08: irq 5, address 00:d0:a8:00:a4:bb
inphy1 at fxp1 phy 1: i82555 10/100 media interface, rev. 4
ppb1 at pci0 dev 20 function 0 "DEC DECchip 21152 PCI-PCI" rev 0x03
pci2 at ppb1 bus 2
ahc1 at pci2 dev 15 function 0 "Adaptec(2) AHA-2940U2 Ultra2" rev 0x00: irq 11
ahc1: Wide Channel A, SCSI Id=7, 16/255 SCBs
scsibus1 at ahc1: 16 targets
ahc1: target 0 using 16bit transfers
ahc1: target 0 synchronous at 40.0MHz, offset = 0xf
sd0 at scsibus1 targ 0 lun 0: <SEAGATE, ST39103LW, 0002> SCSI2 0/direct fixed
sd0: 8683MB, 9772 cyl, 6 head, 303 sec, 512 bytes/sec, 17783240 sec total
isa0 at pcib0
isadma0 at isa0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
sysbeep0 at pcppi0
lpt0 at isa0 port 0x378/4 irq 7
npx0 at isa0 port 0xf0/16: using exception 16
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pccom1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
vt0 at isa0 port 0x60/16 irq 1: vga 80 col, color, 8 scr, mf2-kbd
pms0 at vt0 irq 12
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec
biomask 8840 netmask 8c60 ttymask 9ce2
pctr: 686-class user-level performance counters enabled
mtrr: Pentium Pro MTRR support
dkcsum: sd0 matched BIOS disk 80
root on sd0a
rootdev=0x400 rrootdev=0xd00 rawdev=0xd02

Prev by Date: RE: system/1869: Failed install on Compaq DL-360 server
Next by Date: 700 Saat Bedava Internet ile Yeni Servis Saglayicinizla Tanisin
Previous by thread: OpenBSD 2.9
Next by thread: Panic durring floppy29.fs boot
Index(es):
- Date
- Thread

Visit your host, monkey.org