[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: LaCie USB 2.0 hard drive on OpenBSD 3.5

To: Marco Peereboom <slash@peereboom.us>
Subject: Re: LaCie USB 2.0 hard drive on OpenBSD 3.5
From: Otto Moerbeek <otto@drijf.net>
Date: Sun, 2 May 2004 09:22:33 +0200 (CEST)
Cc: Lawrence Teo <lteo.openbsd1@mailnull.com>, misc@openbsd.org
References: <4094361F.6000503@mailnull.com> <E6A7B3B6-9BF1-11D8-95AE-000A95908CA4@peereboom.us> <40947E5D.407@mailnull.com> <8B350D08-9C03-11D8-95AE-000A95908CA4@peereboom.us>

On Sun, 2 May 2004, Marco Peereboom wrote:

> Hmmm, isn't this thing a little big for a USB key?
> 250059350016 bytes = 232GB; something is screwed up here.

This is not a USB key, it is a real hard disk, with an USB interface:

>>> sd0 at scsibus1 targ 1 lun 0: <WDC, WD2500JB-00FUA0, 15.0> SCSI2
>>> 0/direct fixed
>>> sd0: 238475MB, 238475 cyl, 64 head, 32 sec, 512 bytes/sec, 488397168  

	-Otto

> 
> You need to rig a kernel to do some SCSI debugging to see what the heck  
> is up.
> 
> On May 1, 2004, at 11:51 PM, Lawrence Teo wrote:
> 
> > Here's the output of "disklabel sd0":
> >
> > root# disklabel sd0
> > disklabel: warning, DOS partition table with no valid OpenBSD partition
> > # /dev/rsd0c:
> > type: SCSI
> > disk: SCSI disk
> > label: WD2500JB-00FUA0
> > flags:
> > bytes/sector: 512
> > sectors/track: 32
> > tracks/cylinder: 64
> > sectors/cylinder: 2048
> > cylinders: 238475
> > total sectors: 488397168
> > rpm: 3600
> > interleave: 1
> > trackskew: 0
> > cylinderskew: 0
> > headswitch: 0           # microseconds
> > track-to-track seek: 0  # microseconds
> > drivedata: 0
> >
> > 16 partitions:
> > #        size   offset    fstype   [fsize bsize   cpg]
> >   c: 488397168        0    unused        0     0        # (Cyl.    0 -  
> > 238475*)
> >   i: 488392002       63     MSDOS                       # (Cyl.    0*-  
> > 238472*)
> >
> >
> >
> >
> > Marco Peereboom wrote:
> >> Send us a "disklabel sd0"
> >> On May 1, 2004, at 6:43 PM, Lawrence Teo wrote:
> >>> I ran into problems using a 250GB LaCie P3 USB 2.0 hard drive on an
> >>> OpenBSD 3.5 system, and I was wondering if someone knows the  
> >>> solution.
> >>>
> >>> The problem is that OpenBSD refuses to mount the filesystem on the  
> >>> hard
> >>> drive. The filesystem is formatted as FAT32 but OpenBSD does not  
> >>> want  to
> >>> recognize it:
> >>>
> >>>
> >>> root# mount /dev/sd0i /mnt/usbdrive
> >>> mount_msdos: /dev/sd0i on /mnt/usbdrive: not an MSDOS filesystem
> >>>
> >>> root# mount -t msdos /dev/sd0i /mnt/usbdrive
> >>> mount_msdos: /dev/sd0i on /mnt/usbdrive: not an MSDOS filesystem
> >>>
> >>> root# mount -t msdos /dev/sd0c /mnt/usbdrive
> >>> mount_msdos: /dev/sd0c on /mnt/usbdrive: Inappropriate file type or   
> >>> format
> >>>
> >>> root# mount -t msdos /dev/sd0a /mnt/usbdrive
> >>> mount_msdos: /dev/sd0a on /mnt/usbdrive: Device not configured
> >>>
> >>>
> >>> Here's my fdisk output:
> >>>
> >>>
> >>> -bash-2.05b# fdisk sd0
> >>> fdisk: sysctl(machdep.bios.diskinfo): Device not configured
> >>> Disk: sd0       geometry: 238475/64/32 [488397168 Sectors]
> >>> Offset: 0       Signature: 0xAA55
> >>>          Starting       Ending       LBA Info:
> >>>  #: id    C   H  S -    C   H  S [       start:      size   ]
> >>> --------------------------------------------------------------------- 
> >>> -- -
> >>> *0: 0C    0   1 32 - 238472  44  1 [          63:   488392002 ]  
> >>> Win95  FAT32L
> >>>  1: 00    0   0  0 -    0   0  0 [           0:           0 ] unused
> >>>  2: 00    0   0  0 -    0   0  0 [           0:           0 ] unused
> >>>  3: 00    0   0  0 -    0   0  0 [           0:           0 ] unused
> >>>
> >>>
> >>> My dmesg is as follows (I inserted the USB hard drive after booting   
> >>> up):
> >>>
> >>>
> >>> OpenBSD 3.5 (GENERIC) #34: Mon Mar 29 12:24:55 MST 2004
> >>>     deraadt@i386.openbsd.org:/usr/src/sys/arch/i386/compile/GENERIC
> >>> cpu0: Intel(R) Pentium(R) III Mobile CPU 1200MHz ("GenuineIntel"
> >>> 686-class) 1.20 GHz
> >>> cpu0:
> >>> FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MM 
> >>> X, FXSR,SSE
> >>> real mem  = 267931648 (261652K)
> >>> avail mem = 242102272 (236428K)
> >>> using 3296 buffers containing 13500416 bytes (13184K) of memory
> >>> mainbus0 (root)
> >>> bios0 at mainbus0: AT/286+(00) BIOS, date 11/26/01, BIOS32 rev. 0 @   
> >>> 0xffe90
> >>> apm0 at bios0: Power Management spec V1.2
> >>> apm0: battery life expectancy 100%
> >>> apm0: AC on, battery charge high, charging, estimated 5:45 hours
> >>> pcibios0 at bios0: rev. 2.1 @ 0xf0000/0x10000
> >>> pcibios0: PCI IRQ Routing Table rev. 1.0 @ 0xfbc20/192 (10 entries)
> >>> pcibios0: PCI Interrupt Router at 000:31:0 ("Intel 82371 ISA and IDE"
> >>> rev 0x00)
> >>> pcibios0: PCI bus #4 is the last bus
> >>> bios0: ROM list: 0xc0000/0xd000 0xcd000/0x800! 0xcd800/0x800!
> >>> 0xce000/0x800! 0xce800/0x800! 0xcf000/0x800! 0xcf800/0x800!
> >>> 0xd0000/0x800 0xd0800/0x800! 0xd1000/0x800! 0xd1800/0x800
> >>> 0xd2000/0x800!extent_alloc_region: can't allocate region descriptor
> >>> :12 0xd2800/0x800!extent_alloc_region: can't allocate region  
> >>> descriptor
> >>> :12 0xd3000/0x800extent_alloc_region: can't allocate region  
> >>> descriptor
> >>> :12 0xd3800/0x800extent_alloc_region: can't allocate region  
> >>> descriptor
> >>> :12
> >>> pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
> >>> pchb0 at pci0 dev 0 function 0 "Intel 82815 Hub" rev 0x04
> >>> ppb0 at pci0 dev 1 function 0 "Intel 82815 AGP" rev 0x04
> >>> pci1 at ppb0 bus 1
> >>> vga1 at pci1 dev 0 function 0 "Nvidia GeForce2 Go" rev 0xb2
> >>> wsdisplay0 at vga1: console (80x25, vt100 emulation)
> >>> wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
> >>> ppb1 at pci0 dev 30 function 0 "Intel 82801BAM Hub-to-PCI" rev 0x03
> >>> pci2 at ppb1 bus 2
> >>> esa0 at pci2 dev 3 function 0 "ESS Maestro 3" rev 0x10: irq 5
> >>> ac97: codec id 0x83847609 (SigmaTel STAC9721/23)
> >>> ac97: codec features 18 bit DAC, 18 bit ADC, SigmaTel 3D
> >>> audio0 at esa0
> >>> xl0 at pci2 dev 6 function 0 "3Com 3c556 100Base-TX" rev 0x10: irq 10
> >>> address 00:04:76:49:81:72
> >>> ukphy0 at xl0 phy 0: Generic IEEE 802.3u media interface
> >>> ukphy0: OUI 0x00c000, model 0x0000, rev. 0
> >>> "3Com Mini-PCI V.90 Modem" rev 0x10 at pci2 dev 6 function 1 not   
> >>> configured
> >>> cbb0 at pci2 dev 15 function 0 "Texas Instruments PCI4451 CardBus"  
> >>> rev
> >>> 0x00: irq 10
> >>> cbb1 at pci2 dev 15 function 1 "Texas Instruments PCI4451 CardBus"  
> >>> rev
> >>> 0x00: irq 10
> >>> "Texas Instruments PCI4451 FireWire" rev 0x00 at pci2 dev 15  
> >>> function 2
> >>> not configured
> >>> cardslot0 at cbb0 slot 0 flags 0
> >>> cardbus0 at cardslot0: bus 3 device 0 cacheline 0x8, lattimer 0x20
> >>> pcmcia0 at cardslot0
> >>> cardslot1 at cbb1 slot 1 flags 0
> >>> cardbus1 at cardslot1: bus 4 device 0 cacheline 0x8, lattimer 0x20
> >>> pcmcia1 at cardslot1
> >>> pcib0 at pci0 dev 31 function 0 "Intel 82801BAM LPC" rev 0x03
> >>> pciide0 at pci0 dev 31 function 1 "Intel 82801BAM IDE" rev 0x03: DMA,
> >>> channel 0 wired to compatibility, channel 1 wired to compatibility
> >>> wd0 at pciide0 channel 0 drive 0: <IC25N020ATDA04-0>
> >>> wd0: 16-sector PIO, LBA, 19077MB, 39070080 sectors
> >>> atapiscsi0 at pciide0 channel 0 drive 1
> >>> scsibus0 at atapiscsi0: 2 targets
> >>> cd0 at scsibus0 targ 0 lun 0: <TEAC, CD-224E, 3.7C> SCSI0 5/cdrom   
> >>> removable
> >>> wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 5
> >>> cd0(pciide0:0:1): using PIO mode 4, Ultra-DMA mode 2
> >>> pciide0: channel 1 ignored (disabled)
> >>> uhci0 at pci0 dev 31 function 2 "Intel 82801BA USB" rev 0x03: irq 10
> >>> usb0 at uhci0: USB revision 1.0
> >>> uhub0 at usb0
> >>> uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> >>> uhub0: 2 ports with 2 removable, self powered
> >>> isa0 at pcib0
> >>> isadma0 at isa0
> >>> pckbc0 at isa0 port 0x60/5
> >>> pckbd0 at pckbc0 (kbd slot)
> >>> pckbc0: using irq 1 for kbd slot
> >>> wskbd0 at pckbd0: console keyboard, using wsdisplay0
> >>> pms0 at pckbc0 (aux slot)
> >>> pckbc0: using irq 12 for aux slot
> >>> wsmouse0 at pms0 mux 0
> >>> pcppi0 at isa0 port 0x61
> >>> midi0 at pcppi0: <PC speaker>
> >>> sysbeep0 at pcppi0
> >>> lpt0 at isa0 port 0x378/4 irq 7
> >>> npx0 at isa0 port 0xf0/16: using exception 16
> >>> pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
> >>> fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
> >>> fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec
> >>> biomask 4440 netmask 4440 ttymask 54c2
> >>> pctr: 686-class user-level performance counters enabled
> >>> mtrr: Pentium Pro MTRR support
> >>> dkcsum: wd0 matched BIOS disk 80
> >>> root on wd0a
> >>> rootdev=0x0 rrootdev=0x300 rawdev=0x302
> >>> umass0 at uhub0 port 1 configuration 1 interface 0
> >>> umass0: LaCie LaCie Hard Drive USB, rev 2.00/0.00, addr 2
> >>> umass0: using SCSI over Bulk-Only
> >>> scsibus1 at umass0: 2 targets
> >>> sd0 at scsibus1 targ 1 lun 0: <WDC, WD2500JB-00FUA0, 15.0> SCSI2
> >>> 0/direct fixed
> >>> sd0: 238475MB, 238475 cyl, 64 head, 32 sec, 512 bytes/sec, 488397168  
> >>>  sec
> >>> total
> >>>
> >>>
> >>> I would really appreciate any suggestions on how to solve this  
> >>> problem.
> >>>
> >>> Thanks,
> >>> Lawrence

References:
- LaCie USB 2.0 hard drive on OpenBSD 3.5
  - From: Lawrence Teo <lteo.openbsd1@mailnull.com>
- Re: LaCie USB 2.0 hard drive on OpenBSD 3.5
  - From: Marco Peereboom <slash@peereboom.us>
- Re: LaCie USB 2.0 hard drive on OpenBSD 3.5
  - From: Lawrence Teo <lteo.openbsd1@mailnull.com>
- Re: LaCie USB 2.0 hard drive on OpenBSD 3.5
  - From: Marco Peereboom <slash@peereboom.us>

Prev by Date: Re: LaCie USB 2.0 hard drive on OpenBSD 3.5
Next by Date: Re: LaCie USB 2.0 hard drive on OpenBSD 3.5
Prev by thread: Re: LaCie USB 2.0 hard drive on OpenBSD 3.5
Next by thread: Re: LaCie USB 2.0 hard drive on OpenBSD 3.5
Index(es):
- Date
- Thread