[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

no print to screen (was: Re: testing v 2.8)

To: misc@openbsd.org
Subject: no print to screen (was: Re: testing v 2.8)
From: Alf Breull <puma@hannover.sgh-net.de>
Date: Wed, 01 Nov 2000 14:27:08 +0000


Installation of v 2.8, Oct 21, (or 2.7 from CD) didn't allow print to
screen anymore after appr. 3 minutes, when the audichip (CMI8738/C3DX)
was enabled; dmesg (v 2.8, audiochip enabled) is at the end.

Disabling the audiochip in the BIOS did not allow print to screen 
after several hours (more than 2 hours, less than 12 hours = discovered
next morning).

Furtehr, enabling the audiochip in the BIOS after first reboot, again
did not allow print to screen after appr. after 3 minutes.

Unfortunately, I had to reset in all 3 cases (mainly because there was
'no response' when pressing keys - and I didn't/ don't know any other
way to provoke print to screen again).

Summary of tech information (all SCSI, except for the int. ZIP drive):

P3-733 (Coppermine)/ 133FSB FC BOX, 
1 RAM DIM 256 MB PC133 SDRAM  
P6VAP-A+ mainboard (AMR), via694x & 596B, 3xSDRAM, Audiochip, U-DMA66,
for PGA-Celeron 
Adaptec 29160 ultra 160 SCSI card
HDS 9.1 GB Quantum Atlas V U2LVD 68p
CDS Toshiba XM6401B, 40x, SCSI-2
FLO Teac Floppy 3.5"
Intel EtherExpress Pro 10/100
Cherry G83-6105 LRNDE PS/2 105 keys
PS/2 mouse

The board uses the VIA VT82C694X/ VT82C596B chipset, while v 2.8,
Oct 21, identifies the chipset (errorously ?) as VIA VT82C691/
VT82C598.

As you may imagine, I look forward to run OpenBSD on this box, also 
because I've bought it specially for this reason and selected all
parts according to http://www.openbsd.org/i386.htm.

Please, write if additional information is required.
Any help is welcome.

Alf

---- dmesg (v 2.8, Oct 21) ---

OpenBSD 2.8 (GENERIC) #366: Sat Oct 21 07:21:01 MDT 2000

deraadt@i386.openbsd.org:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: Intel
Pentium III (Coppermine) ("GenuineIntel" 686-class) 732 MHz
cpu0:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,SYS,MTRR,PGE,MCA,CMOV,PAT,PSE36,SER,MMX,F
XSR,SIMD
real mem  = 268021760 (261740K)
avail mem = 243511296
(237804K)
using 3297 buffers containing 13504512 bytes (13188K) of
memory
mainbus0 (root)
bios0 at mainbus0: AT/286+(33) BIOS, date 09/28/00,
BIOS32 rev. 0 @ 0xfb440
apm0 at bios0: Power Management spec V1.2
apm0: AC
on, battery charge unknown
pcibios0 at bios0: rev. 2.1 found at
0xf0000[0xb8c0]
pcibios0: PCI IRQ Routing Table rev. 1.0 found at 0xfdd40,
size 144 bytes (7 entries)
pcibios0: PCI Interrupt Router at 000:07:0 ("VIA
VT82C596A (Apollo Pro) PCI-ISA" rev 0x00)
pcibios0: PCI Exclusive IRQs: 5 9
10 11
pci_intr_fixup: no compatible PCI ICU found: ICU vendor 0x1106
product 0x0596
pcibios0: Warning, unable to fix up PCI interrupt
routing
pcibios0: PCI bus #1 is the last bus
pci0 at mainbus0 bus 0:
configuration mode 1
pchb0 at pci0 dev 0 function 0 "VIA VT82C691 (Apollo
Pro) Host-PCI" rev 0xc4
ppb0 at pci0 dev 1 function 0 "VIA VT82C598 (Apollo
MVP3) PCI-AGP" rev 0x00
pci1 at ppb0 bus 1
"ATI Rage Magnum" rev 0x00 at
pci1 dev 0 function 0 not configured
pcib0 at pci0 dev 7 function 0 "VIA
VT82C596A (Apollo Pro) PCI-ISA" rev 0x23
pciide0 at pci0 dev 7 function 1
"VIA VT82C586A IDE" rev 0x10: DMA, channel 0 configured to compatibility,
channel 1 configured to compatibility
atapiscsi0 at pciide0 channel
1
scsibus0 at atapiscsi0: 2 targets
sd0 at scsibus0 targ 1 lun 0: <IOMEGA,
ZIP 100, 03.H> SCSI0 0/direct removable
sd0: drive offline
sd0: can use
32-bit, PIO mode 3, DMA mode 1
pciide0: channel 1 interrupting at irq
15
sd0(pciide0:1:1): using PIO mode 3, DMA mode 1 (using DMA data
transfers)
"VIA VT83C572 USB" rev 0x11 at pci0 dev 7 function 2 not
configured
pchb1 at pci0 dev 7 function 3 "VIA VT82C596 Power Management"
rev 0x30
ahc1 at pci0 dev 10 function 0 "Adaptec(2) AHA-29160 Ultra160" rev
0x02: irq 11
ahc1: Wide Channel A, SCSI Id=7, 16/255 SCBs
scsibus1 at ahc1:
16 targets
ahc1: target 0 using 16bit transfers
ahc1: target 0 synchronous
at 40.0MHz, offset = 0x3f
sd1 at scsibus1 targ 0 lun 0: <QUANTUM,
ATLAS_V__9_WLS, 0230> SCSI3 0/direct fixed
sd1: 8755MB, 20907 cyl, 2 head,
428 sec, 512 bytes/sec, 17930694 sec total
ahc1: target 2 using 8bit
transfers
ahc1: target 2 synchronous at 20.0MHz, offset = 0x10
cd0 at
scsibus1 targ 2 lun 0: <TOSHIBA, CD-ROM XM-6401TA, 1001> SCSI2 5/cdrom
removable
fxp0 at pci0 dev 11 function 0 "Intel 82557" rev 0x08: irq 10,
address 00:d0:b7:3f:24:16
inphy0 at fxp0 phy 1: i82555 10/100 media
interface, rev. 4
cmpci0 at pci0 dev 13 function 0 "C-Media Electronics
Inc. CMI8738/C3DX Audio" rev 0x10: irq 9
audio0 at cmpci0
isa0 at
pcib0
isadma0 at isa0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC
speaker>
sysbeep0 at pcppi0
lpt0 at isa0 port 0x378/4 irq 7
npx0 at isa0
port 0xf0/16: using exception 16
pccom0 at isa0 port 0x3f8/8 irq 4:
ns16550a, 16 byte fifo
pccom1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte
fifo
vt0 at isa0 port 0x60/16 irq 1: vga 80 col, color, 8 scr, mf2-kbd
pms0
at vt0 irq 12
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
fd0 at fdc0 drive 0:
1.44MB 80 cyl, 2 head, 18 sec
biomask 8840 netmask 8c40 ttymask 9cc2
pctr:
686-class user-level performance counters enabled
mtrr: Pentium Pro MTRR
support
dkcsum: sd1 matched BIOS disk 80
root on sd1a
rootdev=0x410
rrootdev=0xd10 rawdev=0xd12
WARNING: / was not properly unmounted

Follow-Ups:
- Re: no print to screen (add on)
  - From: Alf Breull <puma@hannover.sgh-net.de>

Prev by Date: FLAME ME PRIVATELY
Next by Date: Re: no print to screen (add on)
Prev by thread: FLAME ME PRIVATELY
Next by thread: Re: no print to screen (add on)
Index(es):
- Date
- Thread