Re: kernel/1817: crash during install of 2.9 on Compaq Proliant 1600R

[Michael Shalayeff <mickey@mail.lucifier.net>]

The following reply was made to PR kernel/1817; it has been noted by GNATS.

From: Michael Shalayeff <mickey@mail.lucifier.net>
To: dbt@meat.net
Cc: gnats@openbsd.org
Subject: Re: kernel/1817: crash during install of 2.9 on Compaq Proliant 1600R
Date: Mon, 14 May 2001 23:20:19 -0400 (EDT)

 Making, drinking tea and reading an opus magnum from dbt@meat.net:
 > 
 > >Number:         1817
 > >Category:       kernel
 > >Synopsis:       Compaq ProLiant 1600R crashes
 > >Confidential:   no
 > >Severity:       critical
 > >Priority:       medium
 > >Responsible:    bugs
 > >State:          open
 > >Class:          sw-bug
 > >Submitter-Id:   unknown
 > >Arrival-Date:   Wed May  9 17:40:02 MDT 2001
 > >Last-Modified:
 > >Originator:     David Terrell
 > >Organization:
 > >Release:        2.9
 > >Environment:
 > 	
 > 	System      : OpenBSD 2.9
 > 	Architecture: OpenBSD.i386
 > 	Machine     : i386
 > >Description:
 > 
 > OpenBSD cannot boot on this machine.  If I disable pchb, it can boot but
 > crashes later during install from floppyB29, specifically, during the
 > installation of base29.tgz (about 4MB through the download).
 > 
 > the actual crash error is:
 > fatal page fault in supervisor mode
 > trap type 6 code 2 e0150744 cs 48 eflags 10246 cr2 6c cpl ffffffff
 > panic: trap
 > syncing disks... 384 384 [blah blah gives up]
 > at this point I can type and the console echos my keypresses but I can't 
 > do anything except turn the power off.
 > 
 > I tried disabling eisa to see if it had any impact, but the crash happens
 > regardless.  If I don't disable pchb the machine crashes halfway through
 > the vga1 at ... line during kernel init.
 > 
 > OpenBSD 2.9 (RAMDISKB) #2: Thu May  3 01:39:36 PDT 2001
 >     root@host132:/usr/src/sys/arch/i386/compile/RAMDISKB
 > cpu0: Intel Pentium II ("GenuineIntel" 686-class, 512KB L2 cache) 449 MHz
 > cpu0: FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,SYS,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR
 > real mem  = 268021760 (261740K)
 > avail mem = 244539392 (238808K)
 > using 3297 buffers containing 13504512 bytes (13188K) of memory
 > User Kernel Config
 > UKC> disable eisa
 >  83 eisa0 disabled
 > UKC> disable pchb
 >  49 pchb* disabled
 > UKC> quit
 > Continuing...
 > mainbus0 (root)
 > bios0 at mainbus0: AT/286+(00) BIOS, date 12/30/98, BIOS32 rev. 0 @ 0xf0000
 > pcibios0 at bios0: rev. 2.1 @ 0xf0000/0x2000
 > pcibios0: PCI BIOS has 8 Interrupt Routing table entries
 > pcibios0: PCI bus #2 is the last bus
 > bios0: ROM list: 0xc0000/0x8000 0xc8000/0x4000 0xe8000/0x6000 0xee000/0x2000!
 > pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
 > "Intel 82443BX" rev 0x02 at pci0 dev 0 function 0 not configured
 > vga1 at pci0 dev 11 function 0 "Cirrus Logic CL-GD5446" rev 0x45
 > wsdisplay0 at vga1: console (80x25, vt100 emulation)
 > ppb0 at pci0 dev 13 function 0 "DEC DECchip 21150 PCI-PCI" rev 0x04
 > pci1 at ppb0 bus 1
 > tl0 at pci1 dev 7 function 0 "Compaq ProLiant Netelligent 10/100 TX" rev 0x10: irq 5 address 00:50:8b:2c:31:45
 > nsphy0 at tl0 phy 1: DP83840 10/100 media interface, rev. 1
 > ukphy0 at tl0 phy 31: Generic IEEE 802.3u media interface
 > ukphy0: OUI 0x100014, model 0x0001, rev. 5
 > "Symbios Logic 53c875" rev 0x14 at pci1 dev 9 function 0 not configured
 > "Symbios Logic 53c875" rev 0x14 at pci1 dev 9 function 1 not configured
 > ppb1 at pci1 dev 13 function 0 "IBM 82351 PCI-PCI" rev 0x07
 > pci2 at ppb1 bus 2
 > cac0 at pci2 dev 0 function 0 "Compaq SMART2P RAID" rev 0x03: irq 11 Compaq SMART-2SL
 > scsibus0 at cac0: 1 targets
 > sd0 at scsibus0 targ 0 lun 0: <Compaq, RAID1 volume  #0, > SCSI2 0/direct fixed
 > sd0: 8673MB, 2177 cyl, 255 head, 32 sec, 512 bytes/sec, 17764321 sec total
 > "Compaq Netelligent ASMC" rev 0x00 at pci0 dev 14 function 0 not configured
 > "Intel 82371AB PIIX4 ISA" rev 0x02 at pci0 dev 20 function 0 not configured
 > pciide0 at pci0 dev 20 function 1 "Intel 82371AB IDE" rev 0x01: DMA, channel 0 wired to compatibility, channel 1 wired to compatibility
 > wd0 at pciide0 channel 0 drive 0: <IBM-DTLA-307060>
 > wd0: 16-sector PIO, LBA, 58644MB, 16383 cyl, 16 head, 63 sec, 120103200 sectors
 > pciide0: channel 0 interrupting at irq 14
 > wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2
 > pciide0: channel 1 ignored (disabled)
 > "Intel 82371AB USB" rev 0x01 at pci0 dev 20 function 2 not configured
 > "Intel 82371AB Power Management" rev 0x02 at pci0 dev 20 function 3 not configured
 > isa0 at mainbus0
 > isadma0 at isa0
 > pckbc0 at isa0 port 0x60/5
 > pckbd0 at pckbc0 (kbd slot)
 > pckbc0: using irq 1 for kbd slot
 > wskbd0 at pckbd0: console keyboard, using wsdisplay0
 > npx0 at isa0 port 0xf0/16: using exception 16
 > pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
 > pccom1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
 > fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
 > fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec
 > biomask 4840 netmask 4860 ttymask 4862
 > rd0: fixed, 3560 blocks
 > wd0: no disk label
 > rootdev=0x1100 rrootdev=0x2f00 rawdev=0x2f02
 > 
 > >How-To-Repeat:
 > Attempt to install 2.9
 > >Fix:
 > 
 > Unknown, though now that I look at the dmesg again the two phys on tl0 
 > look odd.
 > 
 > >Audit-Trail:
 > >Unformatted:
 
 which disk did you use as a root drive?
 can you try generic maybe?
 cu
 
 -- 
     paranoic mickey       (my employers have changed but, the name has remained)