[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
i386/1440: Boot floppy error / panic:trap
>Number: 1440
>Category: i386
>Synopsis: Boot floppy error / panic:trap
>Confidential: no
>Severity: critical
>Priority: medium
>Responsible: bugs
>State: open
>Class: sw-bug
>Submitter-Id: net
>Arrival-Date: Wed Oct 11 22:40:01 MDT 2000
>Last-Modified:
>Originator: Mark Stovall
>Organization:
>Release: 2.8
>Environment:
HP NetServer E40
System : OpenBSD 2.8
Architecture: OpenBSD.i386
Machine : i386
>Description:
Greetings,
I'm new to UNIX, so forgive my long winded message.
I'm trying to setup a test BSD box to run 2.8. When I boot with the floppy28 disk I get
the following error.
-----------------------------
reading boot.......
probing: pc0 pci mem[639K 127M a20=on]
disk: fd0 hd0 hd1*
>How-To-Repeat:
boot with the floppy28 disk-
>Fix:
>Audit-Trail:
>Unformatted:
>>OpenBSD/i386 BOOT 1.24
boot>
booting fd0a:/bsd: 1224704+1916928+136764=0x42063c start=0xe0100020
entry point at 0x100020
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
Copyright (c) 1995-2000 OpenBSD. All rights reserved. http://www.openbsd.org
OpenBSD 2.8-beta (RAMDISK) #142: Fri Sep 22 16:49:00 MDT 2000
deraadt@i386.openbsd.org:/usr/src/sys/arch/i386/compile/RAMDISK
cpu0: Intel Pentium Pro ("GenuineIntel" 686-class, 256KB L2 cache) 200 MHz
cpu0: FPU, V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,SYS,MTRR,PGE,MCA,CMOV
real mem = 133804032 (130668K)
avail mem = 120176640 (117360K)
using 1658 buffers containing 6791168 bytes (6632K) of memory
mainbus0 (root)
bios0 at mainbus0: AT/286+(38) BIOS, date 08/01/97, BIOS32 rev. 0 @ 0xf6a83
pcibios0 at bios0: rev. 2.1 found at 0xf6a20[0x940]
fatal page fault in supervisor mode
trap type 6 code 0 eip e01a7463 cs 8 eflags 10246 cr2 8a2 cpl 0
panic: trap
The operating system has halted.
Please press any key to reboot.
---------------------------------
For good measure I tried the floppyB28 and floppyC28 disks and the message only differs
in the "trap type 6 code" line.
I did install the same box using floppy27 without error, and it's running stable.
Here is my dmesg from the 2.7 install.
---------------------------------
OpenBSD 2.7 (GENERIC) #25: Sat May 13 18:04:26 MDT 2000
deraadt@i386.openbsd.org:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: Intel Pentium Pro ("GenuineIntel" 686-class, 256KB L2 cache) 200 MHz
cpu0: FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,SYS,MTRR,PGE,MCA,CMOV
real mem = 133804032 (130668K)
avail mem = 119488512 (116688K)
using 1658 buffers containing 6791168 bytes (6632K) of memory
mainbus0 (root)
bios0 at mainbus0: AT/286+(38) BIOS, date 08/01/97
pci0 at mainbus0 bus 0: configuration mode 1 (bios)
pchb0 at pci0 dev 0 function 0 "Intel 82441FX PCI/Memory (PMC)" rev 0x02
pcib0 at pci0 dev 4 function 0 "Intel 82371SB (Triton II) PCI-ISA" rev 0x01
pciide0 at pci0 dev 4 function 1 "Intel 82371SB (Triton II) IDE" rev 0x00: DMA, channel 0 wired to compatibility, channel 1 wired to compatibility
atapiscsi0 at pciide0 channel 1
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 0 lun 0: <MITSUMI, CD-ROM FX410A !B, J05> SCSI0 5/cdrom removable
cd0: can use 32-bit, PIO mode 3
pciide0: channel 1 interrupting at irq 15
cd0(pciide0:1:0): using PIO mode 3
"Texas Instruments 3DLabs Permedia 2" rev 0x01 at pci0 dev 7 function 0 not configured
ahc1 at pci0 dev 10 function 0 "Adaptec AIC-7850" rev 0x03: irq 11
ahc1: Single Channel A, SCSI Id=7, 3/255 SCBs
scsibus1 at ahc1: 8 targets
ahc1: target 0 synchronous at 10.0MHz, offset = 0xf
sd0 at scsibus1 targ 0 lun 0: <HP, 2.13GB A 50-300U, VCOD> SCSI2 0/direct fixed
sd0: 2033MB, 6810 cyl, 4 head, 152 sec, 512 bytes/sec, 4165272 sec total
ahc1:A:0: no active SCB for reconnecting target - issuing BUS DEVICE RESET
SAVED_TCL == 0x0, ARG_1 == 0xff, SEQ_FLAGS == 0x0
ahc1: Bus Device Reset on A:0. 1 SCBs aborted
ahc1: target 0 synchronous at 10.0MHz, offset = 0xf
ahc1:A:0: no active SCB for reconnecting target - issuing BUS DEVICE RESET
SAVED_TCL == 0x0, ARG_1 == 0xff, SEQ_FLAGS == 0x0
ahc1: Bus Device Reset on A:0. 1 SCBs aborted
probe(ahc1:0:2): Unexpected busfree while idle
SEQADDR == 0x151
ahc1: target 0 synchronous at 10.0MHz, offset = 0xf
ahc1: target 1 synchronous at 10.0MHz, offset = 0xf
sd1 at scsibus1 targ 1 lun 0: <HP, 2.13GB A 50-300U, VCOD> SCSI2 0/direct fixed
sd1: 2033MB, 6810 cyl, 4 head, 152 sec, 512 bytes/sec, 4165272 sec total
ahc1:A:1: no active SCB for reconnecting target - issuing BUS DEVICE RESET
SAVED_TCL == 0x10, ARG_1 == 0xff, SEQ_FLAGS == 0x0
ahc1: Bus Device Reset on A:1. 1 SCBs aborted
ahc1: target 1 synchronous at 10.0MHz, offset = 0xf
ahc1:A:1: no active SCB for reconnecting target - issuing BUS DEVICE RESET
SAVED_TCL == 0x10, ARG_1 == 0xff, SEQ_FLAGS == 0x0
ahc1: Bus Device Reset on A:1. 1 SCBs aborted
probe(ahc1:1:2): Unexpected busfree while idle
SEQADDR == 0x151
ahc1: target 1 synchronous at 10.0MHz, offset = 0xf
xl0 at pci0 dev 12 function 0 "3Com 3c905B 100Base-TX" rev 0x30: irq 10 address 00:50:04:65:5b:aa
exphy0 at xl0 phy 24: 3Com internal media interface
"Cirrus Logic CL-GD5446" rev 0x00 at pci0 dev 13 function 0 not configured
isa0 at pcib0
isadma0 at isa0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
sysbeep0 at pcppi0
npx0 at isa0 port 0xf0/16: using exception 16
vt0 at isa0 port 0x60/16 irq 1: vga 80 col, color, 8 scr, mf2-kbd
pms0 at vt0 irq 12
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec
isapnp0 at isa0 port 0x279: read port 0x203
sb1 at isapnp0 "Creative ViBRA16C PnP, CTL0001, , Audio" port 0x220/16,0x330/2,0x388/4 irq 5 drq 1,5: dsp v4.13
midi1 at sb1: <SB MPU-401 UART>
audio0 at sb1
opl0 at sb1: model OPL3
midi2 at opl0: <SB Yamaha OPL3>
joy0 at isapnp0 "Creative ViBRA16C PnP, CTL7001, PNPB02F, Game" port 0x200/8
biomask 8840 netmask 8c40 ttymask 9c42
pctr: 686-class user-level performance counters enabled
mtrr: Pentium Pro MTRR support
dkcsum: sd0 matched BIOS disk 80
dkcsum: sd1 matched BIOS disk 81
root on sd0a
rootdev=0x400 rrootdev=0xd00 rawdev=0xd02
-----------------------------------------
Hope this helps!
Mark-