[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Re: ESS Maestro3 no sound
- To: Muzaffar Ariff <mus_(_dot_)_bsd_(_at_)_gmail_(_dot_)_com>
- Subject: Re: ESS Maestro3 no sound
- From: Pyun YongHyeon <pyunyh_(_at_)_gmail_(_dot_)_com>
- Date: Fri, 15 Jul 2005 16:06:11 +0900
- Cc: freebsd-multimedia_(_at_)_freebsd_(_dot_)_org
- Reply-to: pyunyh_(_at_)_gmail_(_dot_)_com
On Fri, Jul 15, 2005 at 02:32:54PM +0800, Muzaffar Ariff wrote:
> Ooohhh thats a whole lot of questions, I'll try my best to answer it :)
> > Thanks for your report. It seems that you have other issues not
> > known to me. Does the driver prints timeout message such as
> > "pcm0:play:0: play interrupt timeout, channel dead"?
> Nope, I checked in /var/log/messages and there is nothing wrong with
> it or that line. In fact before I never had that problem.
> > xmms plays songs with normal speed?(i.e. just no sound)
> Yup, xmms plays my mp3s fine, its just no sound is coming out of it.
> I've tried mute & unmute from the function button on the laptop and
> increasing the volume, but nothing seems to happen.
I see. It sounds like Codec issues.
> > Without loading ACPI do you suffer from the same problem?
> If I get you right ACPI means Adv. Configuration and Power Management
> support right? I can unload an ACPI from /boot/loader.conf but there
> are several ACPIs, which one you want me to unload?
You can disable ACPI in loader. If you use beastie menu you can find
a menu item that disables ACPI(probably Safe Mode). If you don't use
beastie menu then you will see a message "Hit [Enter] to boot
immediately, or any other key for command prompt." In that screen,
just press SPACE bar to get OK prompt. Once you get the prompt enter
"set hint.acpi.0.disabled=1" and then enter "boot". Note, depending
on your system booting kernel without ACPI may not work at all.
> > Could show me "pciconf -lv" output for your ESS card?
> pcm0_(_at_)_pci0:8:0: class=0x040100 card=0x00b11028 chip=0x1998125d rev=0x10 hdr=0x00
> vendor = 'ESS Technology'
> device = 'ES1980 Maestro-3 PCI Audio Accelerator'
> class = multimedia
> subclass = audio
> > If you can run "pciconf -lv", locate a line somthing like
> > pcm0_(_at_)_pciX:Y:Z. Then show me output of
> > "pciconf -r pciX:Y:Z 0:ff" before and after loading the drier.
> After loading the driver this is what i got:
> #pciconf -r pci0:8:0 0:ff
> Before (I simply recompiled and install the old maestro3.c driver) I got this:
> # pciconf -r pci0:8:0 0:ff
Oops.. It's typo. It should be read "pciconf -r pci0:8:0 0:0xff".
> Both before and after looks the same. Hope thats what you want.
freebsd-multimedia_(_at_)_freebsd_(_dot_)_org mailing list
To unsubscribe, send any mail to "freebsd-multimedia-unsubscribe_(_at_)_freebsd_(_dot_)_org"
Visit your host, monkey.org