[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Marvell 88E8001 on sk0 and RELENG_5_3 - big problems



> Here's the fix:
> http://www.openbsd.org/cgi-bin/cvsweb/src/sys/dev/pci/if_sk.c.diff?r1=1.51&r2=1.52 <http://www.openbsd.org/cgi-bin/cvsweb/src/sys/dev/pci/if_sk.c.diff?r1=1.51&r2=1.52>
> 
> -- 
> Michal Belczyk


do to severe incompatibility problems with my previous motherboard's IDE and fbsd5.3, i recently purchased
a new gigabyte 865PE, complete with onboard marvell nic. :(

from dmesg (after applying identifying patch)
----
skc0: <Marvell Gigabit Ethernet> port 0xac00-0xacff mem 0xfb000000-0xfb003fff irq 20 at device 9.0 on pci2
skc0: Yukon Gigabit Ethernet 10/100/1000Base-T Adapter
skc0: PN: Yukon 88E8001
skc0: EC: Rev. 1.3
skc0: MN: Marvell
skc0: SN: AbCdEfG5ca025
sk0: <Marvell Semiconductor, Inc. Yukon> on skc0
sk0: Ethernet address: 00:0f:ea:5c:a0:25
miibus0: <MII bus> on sk0
----

unfortuantely, this motherboard too has severe problems. 
although the nic is recognised at install/boot, it simply *refuses* to come up. dhclient just draws a blank.
i have tried to ifconfig sk0 up and down a few times, but makes no difference.

i tried to apply Michal's above patch off an absolute fresh install. ie. the *very* first thing i did
sadly, only 1 of the 2 chunks succeeded.

from if_sk.c.rej
***************
*** 2425,2431 ****
  	/* serial mode register */
  	DPRINTFN(6, ("sk_init_yukon: 9\n"));
  	SK_YU_WRITE_2(sc_if, YUKON_SMR, YU_SMR_DATA_BLIND(0x1c) |
- 		      YU_SMR_MFL_VLAN | YU_SMR_IPG_DATA(0x1e));
  
  	DPRINTFN(6, ("sk_init_yukon: 10\n"));
  	/* Setup Yukon's address */--- 2425,2432 ----
  	/* serial mode register */
  	DPRINTFN(6, ("sk_init_yukon: 9\n"));
  	SK_YU_WRITE_2(sc_if, YUKON_SMR, YU_SMR_DATA_BLIND(0x1c) |
+ 		      YU_SMR_MFL_VLAN | YU_SMR_MFL_JUMBO |
+ 		      YU_SMR_IPG_DATA(0x1e));
  
  	DPRINTFN(6, ("sk_init_yukon: 10\n"));
  	/* Setup Yukon's address */

---

note, i cannot cvsup to latest RLEENG_5, because i have no network! :(
any ideas on what to do from here? 
although the patch did not work automatically, i could manually insert the code, 
but i am well aware of the problems that may cause!

if anyone (in europe) is able to help me solve this issue, i will gladly send them my old ASRock PE ProHT motherboard!
its in perfect condition and works fine with freebsd4.10 - tragically, 5.3 refuses to work with the 
onboard sis IDE controller... 


much thanks,


---
craig.freebsd at online.de