[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: chelsio driver and Myricom driver



You need to use the module in order to update the firmware. The
firmware will be automatically be updated when you up an interface on
the card.

    -Kip

On 7/17/07, Mike Tancsa <mike_(_at_)_sentex_(_dot_)_net> wrote:
Hi,

I am trying to run a recent current with the Chelsio 10GigE card
below and it tries to load but has the following complaint.

cxgbc0: <Chelsio T310 RNIC, 1 port> mem
0xe0201000-0xe0201fff,0xe0800000-0xe0ffffff,0xe0200000-0xe0200fff irq
16 at device 0.0 on pci10
cxgbc0: found wrong FW version (4.0), driver needs version 4.5
cxgbc0: firmware needs to be updated to version 4.5.0
cxgbc0: found wrong TP version (0.0), driver needs version 1.1
cxgbc0: SRAM needs to be updated to version b-1.1.0
cxgb0: <Port 0 10GBASE-CX4> on cxgbc0
cxgb0: Ethernet address: 00:07:43:04:01:2c

Where do I get the firmware from ?  The website only has 4.3 ?  Also,
how do I update the SRAM.  Sorry if these are obvious questions, but
I am new to CURRENT with such drivers.  I have the driver compiled
into the kernel


With the Myricom, it seems to work, but it doesnt detect the cx4
media type for some reason.

# ifconfig mxge0
mxge0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 9000

options=1bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,TSO4>
         ether 00:60:dd:47:c6:c4
         inet 192.168.10.3 netmask 0xffffff00 broadcast 192.168.10.255
         media: <unknown type> (autoselect <full-duplex>)
         status: active

The port is up and I can ping across it so it is working.

TenGigabitEthernet2/3 is up, line protocol is up (connected)
   Hardware is C6k 10000Mb 802.3, address is 0018.bab0.2036 (bia
0018.bab0.2036)
   Description: leopard3 mxge0
   MTU 1500 bytes, BW 10000000 Kbit, DLY 10 usec,
      reliability 255/255, txload 1/255, rxload 1/255
   Encapsulation ARPA, loopback not set
   Full-duplex, 10Gb/s
   input flow-control is off, output flow-control is on
   ARP type: ARPA, ARP Timeout 04:00:00
   Last input never, output 00:00:55, output hang never
   Last clearing of "show interface" counters never
   Input queue: 0/2000/0/0 (size/max/drops/flushes); Total output drops: 0
   Queueing strategy: fifo
   Output queue: 0/40 (size/max)
   5 minute input rate 0 bits/sec, 0 packets/sec
   5 minute output rate 0 bits/sec, 0 packets/sec
      8 packets input, 588 bytes, 0 no buffer
      Received 5 broadcasts, 0 runts, 0 giants, 0 throttles
      0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
      0 input packets with dribble condition detected
      403 packets output, 30468 bytes, 0 underruns
      0 output errors, 0 collisions, 1 interface resets
      0 babbles, 0 late collision, 0 deferred
      0 lost carrier, 0 no carrier
      0 output buffer failures, 0 output buffers swapped out


         ---Mike


--------------------------------------------------------------------
Mike Tancsa,                                      tel +1 519 651 3400
Sentex Communications,                            mike_(_at_)_sentex_(_dot_)_net
Providing Internet since 1994                    www.sentex.net
Cambridge, Ontario Canada                         www.sentex.net/mike

_______________________________________________
freebsd-current_(_at_)_freebsd_(_dot_)_org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-current
To unsubscribe, send any mail to "freebsd-current-unsubscribe_(_at_)_freebsd_(_dot_)_org"

_______________________________________________
freebsd-current_(_at_)_freebsd_(_dot_)_org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-current
To unsubscribe, send any mail to "freebsd-current-unsubscribe_(_at_)_freebsd_(_dot_)_org"


Visit your host, monkey.org