[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

chelsio driver and Myricom driver



Hi,

I am trying to run a recent current with the Chelsio 10GigE card below and it tries to load but has the following complaint.

cxgbc0: <Chelsio T310 RNIC, 1 port> mem 0xe0201000-0xe0201fff,0xe0800000-0xe0ffffff,0xe0200000-0xe0200fff irq 16 at device 0.0 on pci10
cxgbc0: found wrong FW version (4.0), driver needs version 4.5
cxgbc0: firmware needs to be updated to version 4.5.0
cxgbc0: found wrong TP version (0.0), driver needs version 1.1
cxgbc0: SRAM needs to be updated to version b-1.1.0
cxgb0: <Port 0 10GBASE-CX4> on cxgbc0
cxgb0: Ethernet address: 00:07:43:04:01:2c

Where do I get the firmware from ? The website only has 4.3 ? Also, how do I update the SRAM. Sorry if these are obvious questions, but I am new to CURRENT with such drivers. I have the driver compiled into the kernel


With the Myricom, it seems to work, but it doesnt detect the cx4 media type for some reason.

# ifconfig mxge0
mxge0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 9000
        options=1bb<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,JUMBO_MTU,VLAN_HWCSUM,TSO4>
        ether 00:60:dd:47:c6:c4
        inet 192.168.10.3 netmask 0xffffff00 broadcast 192.168.10.255
        media: <unknown type> (autoselect <full-duplex>)
        status: active

The port is up and I can ping across it so it is working.

TenGigabitEthernet2/3 is up, line protocol is up (connected)
Hardware is C6k 10000Mb 802.3, address is 0018.bab0.2036 (bia 0018.bab0.2036)
  Description: leopard3 mxge0
  MTU 1500 bytes, BW 10000000 Kbit, DLY 10 usec,
     reliability 255/255, txload 1/255, rxload 1/255
  Encapsulation ARPA, loopback not set
  Full-duplex, 10Gb/s
  input flow-control is off, output flow-control is on
  ARP type: ARPA, ARP Timeout 04:00:00
  Last input never, output 00:00:55, output hang never
  Last clearing of "show interface" counters never
  Input queue: 0/2000/0/0 (size/max/drops/flushes); Total output drops: 0
  Queueing strategy: fifo
  Output queue: 0/40 (size/max)
  5 minute input rate 0 bits/sec, 0 packets/sec
  5 minute output rate 0 bits/sec, 0 packets/sec
     8 packets input, 588 bytes, 0 no buffer
     Received 5 broadcasts, 0 runts, 0 giants, 0 throttles
     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
     0 input packets with dribble condition detected
     403 packets output, 30468 bytes, 0 underruns
     0 output errors, 0 collisions, 1 interface resets
     0 babbles, 0 late collision, 0 deferred
     0 lost carrier, 0 no carrier
     0 output buffer failures, 0 output buffers swapped out


        ---Mike


--------------------------------------------------------------------
Mike Tancsa,                                      tel +1 519 651 3400
Sentex Communications,                            mike_(_at_)_sentex_(_dot_)_net
Providing Internet since 1994                    www.sentex.net
Cambridge, Ontario Canada                         www.sentex.net/mike

_______________________________________________
freebsd-current_(_at_)_freebsd_(_dot_)_org mailing list
http://lists.freebsd.org/mailman/listinfo/freebsd-current
To unsubscribe, send any mail to "freebsd-current-unsubscribe_(_at_)_freebsd_(_dot_)_org"